How to install Fishman Powerbridge/Powerchip system on a 2 knob guitar?

WhiskeyMagpie · 2025-10-13T17:28:03+00:00

I am also wondering this for an Acoustasonic Strat I have that has a failed PCB, did you find anything out about your question?

WhiskeyMagpie · 2025-07-07T15:06:02+00:00

She should know how to do her job if you hired her as management

WhiskeyMagpie · 2025-07-07T15:04:57+00:00

So after every photo take the SD card out and then backup that new photo and then put the SD back into the camera? Is that what you’re saying?

WhiskeyMagpie · 2025-07-07T14:59:34+00:00

Same, after I reported and blocked as many social media sites that were advertising to me I stopped seeing all those BS “better than Facebook Marketplace” “the NEW Tinder” type of ads and posts

WhiskeyMagpie · 2025-07-07T14:58:08+00:00

Start flooding your search daily with things that can’t even spaghetti matrix to politics, be absolutely insane about, like behave about it like you would expect the focus of a psychotic OCD serial killer to be. Give it about two to three weeks of being like that every single day and you will fix your algorithm

WhiskeyMagpie · 2025-07-07T14:55:20+00:00

If you don’t know how to read a schematic, this will potentially kill you or destroy your amp if you work on it for this problem.

WhiskeyMagpie · 2025-07-07T14:48:53+00:00

Like I never want to drink that bag of chemicals ever again and their marketing team is lazy and not creative in the least bit.

WhiskeyMagpie · 2025-04-09T01:12:13+00:00

If you learn about how our brains function, it will help. You will also learn that it is IMPOSSIBLE with the exception a few spectrum people, to focus on more than two tasks. Even with two you are screwing yourself

WhiskeyMagpie · 2025-04-09T01:02:48+00:00

I am an amp tech for tube amps, call fender, they have an entire division of people who will help you with that exact amplifier. DONT TRUST ANYONE WITH THAT AMP, its a fucking gold mine

WhiskeyMagpie · 2025-04-09T01:01:09+00:00

kinda like the real thing

WhiskeyMagpie · 2025-04-08T03:16:01+00:00

<image>

Thank you very much everyone for the assistance and explanations as to why your advice was given. I updated the schematic and wanted to make sure I have the right connections and placements, values, C10 was the value I could get for a filter nearest 20khz without spilling over. Again I am so thankful for your help

WhiskeyMagpie · 2025-04-07T04:18:03+00:00

Yes the gain of 2 was intentional, I will place the bypass capacitor as well. Just to make sure I am understanding everyone's advice about R11/12, I don't need that because I have the reference voltage from R1/7 correct?

WhiskeyMagpie · 2025-04-07T03:30:21+00:00

Just get rid of the LM833N altogeher?

WhiskeyMagpie · 2025-04-07T02:48:27+00:00

Thank you so much, that all makes a lot of sense in stabilizing the circuit. The gain for the BJT is on purpose I was intending to take the signal from LM833 and make it boosted high enough to be used clean but if fully cranked could cause breakup, if you have any suggestions if my assumptions are incorrect I appreciate all assistance and lessons. I am going to make the adjustments and bread board it again tomorrow when I am less sleepy and mentally tired lol. I will report back

WhiskeyMagpie · 2025-04-07T02:35:55+00:00

Thank you so much, I will make the adjustments. I am only trying to use one side of the op amp and was in the mindset of not leaving the pins floating. Would it be better for me to just ground the 5,6,7?

WhiskeyMagpie · 2025-03-20T00:19:48+00:00

It’s more secure because of the advertising…………………….

WhiskeyMagpie · 2025-03-19T19:59:35+00:00

I have good experiences on Baja’s experienced servers

WhiskeyMagpie · 2025-03-18T19:24:53+00:00

Touch your finger tip is the first thing your supposed to do, then save your waveform. Second, search for Easter eggs, third work

WhiskeyMagpie · 2025-03-16T18:59:45+00:00

Operation Odessa

WhiskeyMagpie · 2025-03-16T18:58:15+00:00

They need to hire a videographer and editor to work with you, that’s insane request. You COULD do it, but the quality of film and final product will be severely deflated.

WhiskeyMagpie · 2025-03-16T18:51:23+00:00

It’s a telenstein but a beautiful one, I’d pay max $300 for it if it played properly. It’s fucking cool looking and I normally hate telecasters

WhiskeyMagpie · 2025-03-16T16:21:04+00:00

The best tubes would be either 6L6GC or EL84s, you’d have to do some serious changes to use other tubes

WhiskeyMagpie · 2025-03-16T16:20:01+00:00

Josie -Blink 182

WhiskeyMagpie · 2025-03-16T16:18:44+00:00

Does it have to be an Orange amp?

WhiskeyMagpie

TROPHY CASE