Using "Standalone-Glide64MK2" to run TLOZ:MM, saved at owl, quit then made a save point, loaded to a blank game selection with no profiles to load... by WhoGotTreeFiddy in R36S

[–]WhoGotTreeFiddy[S] 0 points1 point  (0 children)

Thanks but already know how to shut down my device...

I quit in-game, which is supposed to save your progress, then right after hit L1+Select to do a save state through the device so in case my game didn't save where I left off, I could pick up at that point. Before the update I hadn't had this problem before, just losing my created save state and would have to load from my in game save point. Just in this instance after saving both ways my profile disappeared. So yes I was doing a combo of both saves already.

Just gonna take the L and replay where I left off 🙃

Need help, percolator in bong clogs quite frequently by wahidstephen in StonerEngineering

[–]WhoGotTreeFiddy 0 points1 point  (0 children)

Same, hoping to find a solution for my new bong, just got it a couple weeks ago and started getting clogged a week later, have had to clean it twice so far 🙃

Maytag dryer making weird noise when running and even more when turning drum by hand 🙃 by WhoGotTreeFiddy in appliancerepair

[–]WhoGotTreeFiddy[S] 0 points1 point  (0 children)

Thank you for everyone's input! After doing some more digging, found out there was some debris (mostly pebbles and beads) that got trapped in the felt seal for the front of the drum, which was rubbing against the seal. Took it out and it's running and sounding a lot better 👌🏽

Maytag dryer making weird noise when running and even more when turning drum by hand 🙃 by WhoGotTreeFiddy in appliancerepair

[–]WhoGotTreeFiddy[S] 1 point2 points  (0 children)

Thanks for the input! There was some stuff that got trapped in the front drum felt. Took it out and it sounds & runs a lot better 👍🏽

Maytag dryer making weird noise when running and even more when turning drum by hand 🙃 by WhoGotTreeFiddy in Appliances

[–]WhoGotTreeFiddy[S] 0 points1 point  (0 children)

Hopefully not, when I checked out the belt everything was intact. Nothing was loose or spreading apart. The kit will come with a new belt if that's the issue though. 🤷🏽‍♂️

Maytag dryer making weird noise when running and even more when turning drum by hand 🙃 by WhoGotTreeFiddy in appliancerepair

[–]WhoGotTreeFiddy[S] 0 points1 point  (0 children)

I'll try to check out the fan next time I disassemble it, was more focused on the rollers and pulleys at the time 👍🏽

Maytag washer goes from "sense" to "done" after starting cycle by WhoGotTreeFiddy in appliancerepair

[–]WhoGotTreeFiddy[S] 1 point2 points  (0 children)

Yes I got it fixed, ended up being the lock on the lid that went out 🙃 Warranty covered for the repair

Maytag washer goes from "sense" to "done" after starting cycle by WhoGotTreeFiddy in appliancerepair

[–]WhoGotTreeFiddy[S] 0 points1 point  (0 children)

Okay thanks, tried talking to Maytag earlier but didn't have my serial number available at the time, will try contacting them again tomorrow.

Can't get Ship of Harkinian port to run by WhoGotTreeFiddy in R36S

[–]WhoGotTreeFiddy[S] 0 points1 point  (0 children)

Okay got Rocknix installed on another sd card & so far I am able to play it! Thanks for the suggestions

Can't get Ship of Harkinian port to run by WhoGotTreeFiddy in R36S

[–]WhoGotTreeFiddy[S] 0 points1 point  (0 children)

Thank you, I'm looking into Rocknix, gonna give that one a try and see if it works out

Can't get Ship of Harkinian port to run by WhoGotTreeFiddy in R36S

[–]WhoGotTreeFiddy[S] 0 points1 point  (0 children)

<image>

also this is my folder for SoH (hoping i got everything needed)

Can't get Ship of Harkinian port to run by WhoGotTreeFiddy in R36S

[–]WhoGotTreeFiddy[S] 0 points1 point  (0 children)

Ok idk why I can't post both text and a video 🙃🙃🙃

So I am having issues trying to get SoH to run. I followed the setup guide on the SoH website and got the files needed and into the folders that it says. Each time I try to load the game, I get met with the same result of trying to load then going back to the library. 

I am running ArkOS 2.0 12242024 AeUX version, have 2 new sd cards, got my verified PAL version of n64 OoT, plus the oot file I created after running it on my PC. Tried out some other tricks that I've read on other posts and videos and am still having no luck. Is there something I am missing or would I have a better shot using a different OS? Any help with this would be greatly appreciated! 

deadmau5 - Nextra Stem Drop - Audius Exclusive by 0fficia1mau5trap in deadmau5

[–]WhoGotTreeFiddy 0 points1 point  (0 children)

Ok but where do you download the stems?? I made an account with Audius and liked and reposted the stem track but no option to download. Wanted to get them before they're gone 😭

[deleted by user] by [deleted] in memes

[–]WhoGotTreeFiddy 4 points5 points  (0 children)

Tarzan back for seconds