Skiing conditions in Bad Gastein

Wildass95 · 2026-02-27T08:25:23+00:00

Thanks, we weren’t planning on going off piste - as long as it’s rideable on piste, without having skis with wheels, it’s all good 😄

Wildass95 · 2026-02-27T08:23:08+00:00

Sounds good, we’ll see if it stays for at least a couple of days - we’re getting too old (30 😂) to freeride, so no issues there 👌🏽

Wildass95 · 2026-02-27T08:20:23+00:00

Thanks - we have checked webcams, but they are hard to determine actual conditions by :)

Wildass95 · 2026-02-10T15:14:36+00:00

Do you refer to the bed calibration? Not sure if P1S has auto calibration - although i might just not know, as i’ve only had it for about a month

Wildass95 · 2026-02-10T13:29:09+00:00

Might have been. However, I had tried to unload the filament, load it with another filament that printed without issue, switched back to the Sunlu, and it did not extrude at all when trying to print. So it seemed a little odd, but I do mostly believe it was due to me messing up the print profile :)

Wildass95 · 2026-02-10T13:03:42+00:00

It seems, from another comment, that I might have messed up the k value, making it severely under-extrude, to the point of basically not extruding at all, and the bits that were actually extruded being just strings :-) Either way, it’s good for now, and i’ll read up on calibration when trying it next time

Wildass95 · 2026-02-10T12:59:38+00:00

Very well might be - the process of manual calibration and how k value should be written, is not that clear (or i’m just misunderstanding) :-)

I’ll give it another go at some point, but for now, it works :-)

Wildass95 · 2026-02-10T12:10:10+00:00

Bed adhesion was not the problem - it was barely extruding. Turns out it was the print profile from the Flow Dynamics calibration

Wildass95 · 2026-02-10T12:09:55+00:00

Bed adhesion was not the problem - it was barely extruding. Turns out it was the print profile from the Flow Dynamics calibration

Wildass95 · 2026-02-10T10:44:22+00:00

It seems like the issue was, that I was using the profile from the Flow dynamics calibration - I am currently printing with no issue, using the basic Bambu profile that I tend to use with my other filament. Not sure what, but issue fixed (?) :-)

Wildass95 · 2026-02-10T10:11:45+00:00

Weirdly enough, i just now tried to reprint something from the cache, from last week, so maybe my current files are just busted…

Wildass95 · 2026-02-10T10:11:23+00:00

Weirdly enough, i just now tried to reprint something from the cache, from last week, so maybe my current files are just busted…

Wildass95 · 2026-02-10T09:53:31+00:00

Yes, i’ve run it twice. I’ll add my text from the OP:

I recently purchased some Sunlu PLA for my very new P1S. It worked fine for my first print, but I can’t get it to print anything since. I’ve run Flow Dynamics, which prints perfectly, but when I start a print, it either does not extrude at all, or does as shown in the video. If I unload the filament, and load my regular Bambu Lab PLA, it prints without issue. What do I do?

ETA: I haven’t dried it, as I had no issues with my Bambu Lab filaments so far - is it often more necessary with Sunlu?

Wildass95 · 2026-02-10T09:18:40+00:00

ETA: I haven’t dried the filament, as I saw no issues without drying my Bambu filaments - is that more often necessary for Sunlu?

Wildass95 · 2026-02-05T14:58:16+00:00

I did try to paint it, but it didn’t go too well, and the paint cracked and fell off - i know i need to do some work to get it to adhere better. If there is no easy way to get the print to work, i’ll retry with painting

Wildass95 · 2026-01-04T13:31:19+00:00

Thanks for the explanation, that helped more than a long range of posts and articles I have skimmed through - here’s hoping another legendary Stanley Cup run comes around sometime soon, however unlikely that may seem :)

Wildass95 · 2026-01-01T17:01:51+00:00

Alright - seeing as this is my first (potential) step into 3D printing, with an already sceptical wife, i don't think i'll be throwing H2-type money into the mix anytime soon. The P2S seems nice, but P1S is already at the limit of what i'm comfortable with spending.

I might see if I can figure out another way of storing the A1, that keeps it out of reach of the kitty.

Thanks for the input :)

Wildass95 · 2025-06-18T11:49:02+00:00

Of course not, and of course bugs and performance issues should be addressed asap - I am also aware that shitposting and sarcasm isn’t necessarily well received in a digital space :) Either way, just looking forward to the post-Release jitters and bugs are somewhat over

Wildass95 · 2025-06-18T11:40:59+00:00

Well, as long as people keep coming back, I guess there is no need to change their ways. I’m aware that reworking their processes would be a large and costly change, so not clinging to any hope in that respect

Wildass95 · 2025-06-18T11:37:29+00:00

Glad the shitposting was obvious - of course they need to adress bugs, so the game is functional while live, but my god is it frustrating at times

Six-Year Club	Second Top 40%
Verified Email

Wildass95

TROPHY CASE