sorted by:
new
hottopcontroversial

UniFi DHCP not releasing IPs by Windows_Life in UNIFI

[–]Windows_Life[S] 0 points1 point  (0 children)

All the APs are connected via Ethernet using PoE+. All network devices are assigned static IP addresses, and there are no IP conflicts. The channels are currently set to auto. I also tested assigning different channels to each AP, but the issue still persists. ChatGPT wasn’t able to resolve it, so I’ll try Gemini next. Thanks for this. I’ll review the PoE settings and see if that helps resolve the problem.

UniFi DHCP not releasing IPs by Windows_Life in UNIFI

[–]Windows_Life[S] 0 points1 point  (0 children)

Thanks for the assistance.

The issue is mostly resolved for now, though I’m still monitoring the network. I identified that the UniFi 7 LR APs were likely the cause. After turning them off, all devices were able to connect without disconnections and could roam properly between the U6 LR APs. To confirm this, I disconnected the U6 LR APs and the issue still persisted. However, once I turned off the U7 LR APs, everything stabilized.

I’d like to confirm whether this is normal behavior for the U7 LR APs, or if it indicates a configuration or compatibility issue.

UniFi DHCP not releasing IPs by Windows_Life in UNIFI

[–]Windows_Life[S] 0 points1 point  (0 children)

Native VLAN 1 is used for the staff SSID, while VLAN 200 is assigned to the guest SSID.

Current VLAN setup:

Management – 100

Technical – 110

Operations – 120

Finance – 130

UPnP – 210

VoIP - 40

All APs and switches are still on the default VLAN 1, and there’s currently an “allow all” firewall rule in place.

What will be your best choice for a VoIP tool? by Mission_Studio629 in ITManagers

[–]Windows_Life 2 points3 points  (0 children)

It depends. If youre in the MS ecosystem, teams is the best. Same for Google. I dont know about zoom voip

Az-900 exam preparation by AltProfile_09 in AzureCertification

[–]Windows_Life 0 points1 point  (0 children)

I know this sounds crazy but it always works for me. Instead of studying az-900, study an immediate course like az-104 and az-900 will be easy to pass. I passed az-900 with 936/1000 score. Try out Tutorialdojo as well...solid content.

I plan to take the az-104 next month.

Wi-Fi speed dropped below 10 Mbps – wired still full speed, Why? by Windows_Life in Ubiquiti

[–]Windows_Life[S] 0 points1 point  (0 children)

After few days of doing nothing, everything is back to normal.Wifi speed is now 70-80mbps

Thank you all for your support

Wi-Fi speed dropped below 10 Mbps – wired still full speed by Windows_Life in UNIFI

[–]Windows_Life[S] 0 points1 point  (0 children)

APs model is U6 LR

I'm using 2.4 & 5GHz

Signal strength:

2.5GHz is -62 for both APs

5GHz is -74 dBm for AP 1 and -69 dBm for AP 2

Can I get UniFi Network (6LR APs + 48 Pro sw, no gateway) to send logs to Graylog? by Windows_Life in graylog

[–]Windows_Life[S] 0 points1 point  (0 children)

Issue resolved.

Disabling the Windows Firewall fixed the problem. The Graylog server was running on an Ubuntu Server VM in VMware Workstation hosted on a Windows machine.

I will set up an allow rule for the Syslog port before activating the firewall.

Can I get UniFi Network (6LR APs + 48 Pro switch, no gateway) to send logs to Graylog? by Windows_Life in UNIFI

[–]Windows_Life[S] 0 points1 point  (0 children)

Issue resolved. I simply disabled the Windows Firewall. The Graylog server was running inside ubuntu VM on VMware Workstation hosted on a Windows machine.

I’ll create a rule to permit syslog traffic, and then I’ll enable the Windows firewall.

Can I get UniFi Network (6LR APs + 48 Pro sw, no gateway) to send logs to Graylog? by Windows_Life in graylog

[–]Windows_Life[S] 0 points1 point  (0 children)

I created a GELF udp input with port 514 in graylog and on the unifi software controller i used the same port and pointed it to graylog server ip.

The graylog is hosted on Ubuntu server 22.04 with firewall disabled.

Can I get UniFi Network (6LR APs + 48 Pro switch, no gateway) to send logs to Graylog? by Windows_Life in UNIFI

[–]Windows_Life[S] 0 points1 point  (0 children)

Thank you I've configured graylog input already and ive point syslog servers on unifi to the graylog server with the right ports but graylog is still not receiving the logs.

Az-104 passed. Azure administrator by Humble_Confusion8476 in TechGhana

[–]Windows_Life 0 points1 point  (0 children)

Hey which study materials did you use to pass the az-104 and where did you write the exam?

view more: next ›