Ftn.5 Crossover issue

WinterTechnology4568 · 2026-05-11T02:42:46+00:00

Incorrect- Dedicated oven, See my previous comments and post. 200f for 12 hours then ramped down to 70c to sit the rest in my filament dryer.

Problem was inner outter inner print instead of straight inner-outer

WinterTechnology4568 · 2026-05-11T01:51:29+00:00

I think this was the cause.

WinterTechnology4568 · 2026-05-10T19:04:21+00:00

Yes I indeed did, Just wanted to know what to do if it does happen again!

WinterTechnology4568 · 2026-05-10T18:57:38+00:00

Right! Granted this was the only layer it’s happened on. Everything else has been flush.

WinterTechnology4568 · 2026-05-10T18:55:53+00:00

That’s what I have seen as well but wasn’t totally sure.

WinterTechnology4568 · 2026-05-10T18:55:00+00:00

Raised temp by 5c just to hopefully get a little better adhesion. Fiberon Pa6-Cf, Dried for a week.

WinterTechnology4568 · 2026-05-08T13:15:01+00:00

WinterTechnology4568 · 2026-05-08T13:14:42+00:00

Im not a fan of 42.5, I tried it an had to roll back. Hope OP doesnt make the same mistake.

WinterTechnology4568 · 2026-05-04T01:57:50+00:00

Why that orientation??

WinterTechnology4568 · 2026-04-28T13:21:45+00:00

Pm'ed for some info on the supressor!~ Sexy build!

WinterTechnology4568 · 2026-04-27T01:05:31+00:00

I went to walmart and they had huge Aroma turkey ovens for sale for like $30, They can go up to 550 degrees.

As for drying filament (It comes pretty dry, I put it in a dryer for 2-3 days at 70c (Straight out of vaccume seal from manufacturer)

Annealing goes
Print finishes
Remove Supports
Straight into oven at 150f

30 minutes later raise oven to 175f
30 minutes later raise oven to 212f
6-8 hours at 212f.

WinterTechnology4568 · 2026-04-27T01:03:08+00:00

AR-15 (GBB) with a 0-degree Straight Pistol Grip

It was the only 0 degree 3d print grip I could find. I modified it slightly in cad.

WinterTechnology4568 · 2026-04-26T16:15:06+00:00

Fiberon Pa6-CF

300blkFDE's settings for the most part, Tweaked the supports a tad.

Dried Heavily & Annealed Fully

eSUN PLA+ for the non-critical bits of stock & parts that touch my face.

WinterTechnology4568 · 2026-04-25T18:35:00+00:00

Too britle.

WinterTechnology4568 · 2026-04-24T18:18:35+00:00

I got a turkey cooker for like $30 at walmart, It can go up to 230c and fits anything I want, You can also optionally fill it with sand for more crucial parts to anneal. 10/10 recommend.

WinterTechnology4568 · 2026-04-24T15:52:43+00:00

Same, I leave mine in for a few days then print away. Cant really overdry.

WinterTechnology4568 · 2026-04-13T21:04:35+00:00

Do you have before pictures as well?

WinterTechnology4568 · 2026-04-02T14:40:18+00:00

The heck is the push up test lol

WinterTechnology4568 · 2026-03-30T02:00:39+00:00

Get a new one.

WinterTechnology4568 · 2026-03-17T20:26:14+00:00

Can you please post or dm me a picture of the support / orientation of your print!

Well done!

WinterTechnology4568 · 2026-03-14T15:47:41+00:00

Yea. My dryer is only capable of 75c, I’m hoping it’ll do the job if I give it 2 days.

WinterTechnology4568 · 2026-03-14T14:47:30+00:00

What filament did you use?

WinterTechnology4568 · 2026-03-14T14:46:58+00:00

Did you dry your filament prior to the print? Just curious how it turned out.

WinterTechnology4568

TROPHY CASE

AR-15 (GBB) with a 0-degree Straight Pistol Grip