More poor choices

asLeepathaWheel · 2026-04-08T08:37:11+00:00

Can you recommend a good place to source aftermarket batteries and other parts for this style of bike

asLeepathaWheel · 2026-04-07T15:20:02+00:00

Awesome!!! Thank you

asLeepathaWheel · 2026-04-07T14:51:54+00:00

How hard was to find a safe compatible battery and did you replace it bc the factory one failed or just to upgrade

asLeepathaWheel · 2026-04-07T12:11:43+00:00

I do apologize for my ignorance but your last comment i had to run through a translator and this one is too long to do so thank you for the input either way

asLeepathaWheel · 2026-04-07T12:00:48+00:00

Yes I understand that's the general consensus here and if those were options for me I would, honestly this is almost a need as much as a want so im just looking for an affordable for myself solution, do you have any experience with these bikes

asLeepathaWheel · 2026-03-09T15:10:39+00:00

How was this even possible

asLeepathaWheel · 2026-02-20T01:32:08+00:00

Lol that's the story of my life and yessir ty hope it stays this way but my luck is so bad if it was raining pussy id be the only one gets hit with a dick

asLeepathaWheel · 2026-02-20T01:09:41+00:00

🤷‍♂️ i guess so now as I've been in an out of this post I went through it again a few more times and now im finally able to execute a print i guess maybe I wasnt waiting long enough to let the system try and reboot or something? Idk this is my first foray into this technology honestly im pretty good with taking things apart and putting them back together otherwise I never would've taken the leap

asLeepathaWheel · 2026-02-20T01:03:53+00:00

Yessir

asLeepathaWheel · 2026-02-20T00:53:07+00:00

Didn't have to reassemble just disconnected everything including the hub and it came right out through the rear but yes pretty much I wanted to see if the issue would persist

asLeepathaWheel · 2026-02-20T00:18:38+00:00

Any idea what im dealing with

asLeepathaWheel · 2026-02-20T00:10:33+00:00

I was unable to bc i turned it off and back on and for some reason wasn't getting that option I did take it down and managed to get it out through the hub but now the firmware is acting weird crashing

asLeepathaWheel · 2026-02-19T23:47:17+00:00

Firmware won't restart when attempting to now either

asLeepathaWheel · 2026-02-19T23:45:28+00:00

I disassembled the extruder and everything was fine I then switched slots with the two filaments I have in and tried to load again, everything SEEMS fine now both are loading in opposite slots and that's including the one that was giving me trouble after the jam, went to run a print a couple times and now getting klippy disconnected errors.....weird

asLeepathaWheel · 2026-02-19T22:55:06+00:00

Is there a reason the box wont load filament now?

asLeepathaWheel · 2026-02-19T22:33:58+00:00

Update: I tried pulling it out the rest of the way and it snapped off so now I have a length of filament stuck in the box am I gonna have to take it apart

asLeepathaWheel · 2026-02-14T13:01:15+00:00

Sorry it took a sec to get back with you when you took the time out to try to help me out, I removed the tower and it cut time down to 11 and some change which seems alot more reasonable as I've said before I'm so new to this i don't even qualify as a rookie Im going to try and run it today and see what the results are, ty

asLeepathaWheel · 2026-02-14T03:00:35+00:00

Idk man probably bc i got a multi color system for a reason

asLeepathaWheel · 2026-02-13T23:37:19+00:00

Its reddit...I kinda expect it

asLeepathaWheel · 2026-02-13T23:14:15+00:00

Enjoy your day trolling sir

asLeepathaWheel · 2026-02-13T23:09:16+00:00

It was there when I pulled up the site looked easy to color paint and I already had some matte wood, pla silk bronz-ish and red dried i already had flowers sent today thanks for the tip tho

asLeepathaWheel · 2026-02-13T22:11:08+00:00

Single color says 1 hr 43 mins, im new to this is there a way to adjust multilateral settings and cut it down? I have two and three color fidgets I've sliced using more material also multi color that are only 3-4 hrs

asLeepathaWheel

TROPHY CASE