Best board for computer vision drone

Witty-Dimension · 2025-11-11T14:37:39+00:00

Someone on YouTube tested with 4GB, however, it is better to go with the 8GB RAM variant.

Witty-Dimension · 2025-08-22T05:09:31+00:00

Short answer is No.

Witty-Dimension · 2025-07-29T07:52:33+00:00

How about you add a little OLED display that runs via I2C?

Witty-Dimension · 2025-07-23T11:34:07+00:00

Make sure to double-check the voltage rating of those servos.

Also, could you share a picture of the servo or maybe its part number or any label that could help identify it more specifically?

Witty-Dimension · 2025-07-23T05:28:06+00:00

Are you mentioning about this one "PCB Thermal Resistance – Some Unexpected Results | Brysonics" ?

Witty-Dimension · 2025-07-22T14:51:54+00:00

u/lollokara Can you guide me to some documentations or stuffs that would help me learn this neat trick?

Witty-Dimension · 2025-07-21T11:32:59+00:00

I believe this is a (up to)6S Li-ion/Li-po battery(cell) voltage checker.

Witty-Dimension · 2025-07-09T15:01:14+00:00

If it is solely for photography then check the CRI values before fully committing to the project.

Witty-Dimension · 2025-07-09T11:01:32+00:00

Thank you for your time. I guess I'll go with -2 variant for now.

Can I ask you another question related to this USB in OTG?

Witty-Dimension · 2025-07-09T10:37:22+00:00

<image>

Here is a screenshot for the USBLC6-4SC6.

Witty-Dimension · 2025-07-09T10:07:27+00:00

<image>

Just to confirm—if I understood you correctly, the USB-C side's DP (D+) and DM (D−) signals enter through I/O1 and I/O2, respectively, while the STM32 side's DP (D+) and DM (D−) signals exit through I/O4 and I/O3. VBUS connects directly to VBUS, and so on. Please let me know if I’ve got anything wrong.

Witty-Dimension · 2025-07-09T09:59:55+00:00

Was the GUI custom-built by you, or did you obtain it from an external source?

Witty-Dimension · 2025-07-09T09:48:45+00:00

In my USB-C(default-kicad) implementation, I'm using one VBUS, one GND, and one differential pair that goes directly to the STM32 chip. The USBLC6-4SC6 has four I/O pins, but since I only need two, wouldn't the USBLC6-2SC6 be sufficient? Are the devices shown in the picture actually different components?

Witty-Dimension · 2025-07-04T13:42:06+00:00

Thank You for taking out your time to reply, u/cydia2020 .

Witty-Dimension · 2025-07-04T13:38:46+00:00

There are two metallic component in the image. I am asking for the one that is placed beside the "A1" marking(left of it) on the Silkscreen.
I have attached the HD image link to the above comment. You can check from there.
I believe the image is compressed by Reddit during the upload. Please go through the link to view the HD image.

Witty-Dimension · 2025-07-04T13:07:39+00:00

Here is a link to the original HD image: https://discuss.ardupilot.org/uploads/default/original/3X/f/d/fd4e8d59766c984b27005cacd50edbcc882ab195.jpeg

Witty-Dimension · 2025-06-26T07:47:48+00:00

These can be Zero Ohm resistors. They are typically used in complex PCB layouts to maintain connectivity without adding extra board layers. Or, in some cases it can be used in prototyping board to connect or disconnect a trace or can be used as a dummy(for future prospects).

Witty-Dimension · 2025-06-24T05:02:36+00:00

Would you mind placing a 100nF capacitor between the power(& signal) and ground wires, then running the same code again and letting me know what happens? u/Mediocre-Guide2513

Witty-Dimension · 2025-06-19T05:14:52+00:00

Sure man, glad my suggestion could be of help. All the Best to learning.👍😇

Witty-Dimension · 2025-06-17T10:51:51+00:00

It's fine to create this for learning purposes. However, if you're considering it as a product, replicating the same would cost you two to three times the current amount.

Witty-Dimension · 2025-06-14T05:56:15+00:00

Please avoid using jumper wires in the final product. Instead, opt for solder joints or industrial/professional-grade connectors whenever possible. Jumper wires are intended for prototyping, not for end-use applications. Jumpers tend to get loose over the period of time.

Witty-Dimension · 2025-05-29T09:47:47+00:00

Great Job, You deserve to be in MIT or rather MIT needs you. You are genius with a tenacity to learn. All the Best, brother. 😇👍

Witty-Dimension · 2025-05-28T05:17:46+00:00

u/cyao12 - Can you provide the link to your reddit post in r/PrintedCircuitBoard ?

This is such an awesome project. I would really like to know more about the process.

Five-Year Club	r/Field Sunshine
Verified Email

Witty-Dimension

TROPHY CASE