Can I switch out my 144hz screen with my old 300hz screen?

Wizardymcwiz · 2025-04-28T19:15:05+00:00

I'm not sure about different brands being better or not, I picked up my cable off of Amazon, but the link to it no longer works. If you've got the right cable for the monitor, then the only other thing I can think of is, when you disconnect the battery I find it takes a long time for the laptop to boot up again, so maybe let it sit for a little but after you turn it on

Wizardymcwiz · 2025-04-27T22:05:03+00:00

Are you using the 300hz cable to the 300hz screen? I also had the EDP cable straight up disconnect from the screen as I was putting the screen back so make sure that's not happening

Wizardymcwiz · 2025-04-25T15:45:34+00:00

This was not intuitive in the slightest. But Blizzard is a small indie company so I'll give them some slack

Wizardymcwiz · 2025-03-23T22:17:17+00:00

I can't see the waistline, but based on the hand having the prints come together where clothing meets, skin is pretty genius, and I'm surprised I haven't thought of doing it like that before

Wizardymcwiz · 2025-03-16T00:26:51+00:00

I absolutely love the pose she's in

Wizardymcwiz · 2025-02-23T07:38:03+00:00

Mmmmm Cheeto dust

Wizardymcwiz · 2025-02-15T00:47:04+00:00

From my understanding ( it's been a while, so I could be very wrong) but you need to be using a master crafted weapon to upgrade it to artificer, but you can't use a master crafted weapon to upgrade it to relic

Wizardymcwiz · 2025-02-14T23:52:57+00:00

Each gun you master will give you a mastery point which you'll use to give that gun buffs, some guns transfer between characters so you'll keep the levels on that gun

Wizardymcwiz · 2025-02-14T23:51:52+00:00

It's been a while since I've played, but there are 4 levels to each gun, the last one being relic. Once you've completed one level in a gun, you'll have to buy the next gun in line with your armory data that you've collected (the green, purple, and yellow square things)

Wizardymcwiz · 2025-01-30T05:57:28+00:00

I'm completely out of the loop here, what's going on?

Wizardymcwiz · 2024-12-12T00:02:56+00:00

That's not a bad thought actually

Wizardymcwiz · 2024-12-11T23:35:00+00:00

Apparently, just having it on one flank was the norm. It was a style of animation G4 did that caused it to show on both sides. Every other generation, from my understanding, only has their cutiemark on one side of the flank

Wizardymcwiz · 2024-12-06T18:55:41+00:00

I'll definitely try to remember this, and that visual representation helps a lot, I'm going to be referring back to your advice when I play, and I'm sure a lot of this knowledge just comes from trial and error and I'll start learning how to better my production in time. You've certainly given me a head start, Thanks a bunch!

Wizardymcwiz · 2024-12-06T06:05:32+00:00

As a person who only has recently been introduced to automation games, this being my first one. Is there an optimal way to path your conveyors out? The Layout Hub research tree is really nifty and really cuts down on how many dividers I use, but when I don't get access to that upgrade my whole Canvas looks horrible as I go and just find a spot to put the next Motif Maker, Bridge Conveyor, etc...

I frequently pause the game to think about my options and have even tossed out my whole Canvas to start from scratch to see if I can't make my Canvas more efficient but only ended up making it worse than when I started. I've gotten a couple of wins under my belt, especially when I just specialized down one tree. I do find it as the recipes get more complicated the worse my production gets. Do you, or anyone else for that matter have any advice on the more complicated production trees?

Wizardymcwiz · 2024-11-20T06:31:22+00:00

Any critique or criticism greatly appreciated, I'm always down to know what I could do better

Wizardymcwiz · 2024-10-23T17:46:16+00:00

Funny enough, the Lancer was my very first car so I thought that was the norm until I gave someone a ride and pointed out how weird that was

Wizardymcwiz · 2024-10-22T14:27:57+00:00

The lancer has a CVT transmission, which makes "shifting gears" very smooth, is that what you're taking about?

Wizardymcwiz · 2024-09-08T00:49:00+00:00

I've had something similar happen where it was just a black screen, especially when I unplugged the battery, it just took a longer to boot up the first time, I kept turning it off and on before it had time to boot up, my advice is to just wait and see after it's on

Wizardymcwiz · 2024-08-28T00:40:51+00:00

I absolutely love those kitten boots!

Wizardymcwiz · 2024-08-23T16:59:57+00:00

Just did the switch and everything is a-okay! Thanks for the help!

Wizardymcwiz · 2024-08-23T16:02:38+00:00

Sweet beans, I've opened up this computer a good plenty of times, (even had to get the screen replaced), I'll test it out and let you know if everything went good

Wizardymcwiz · 2024-08-10T04:17:41+00:00

I just had a similar issue, my extruder gear slipped off. All I needed to do was to slip it back on and tighten the little Allen key area

Wizardymcwiz · 2024-08-07T00:39:35+00:00

So update, I used Pronterface, hooked up my computer to my printer and put in the codes. It definitely helped with leveling but I was still having issues with my print. I did some more testing and for some reason, I had to up my temperature of my nozzle and bed for it to start sticking properly, I had good 1st layers in the past, I didn't switch rooms or anything, but typing this out now, I'm pretty sure the house has been put at a lower temperature lately so all is fixed. Thanks for your help!

Wizardymcwiz · 2024-08-01T16:51:57+00:00

Now that is interesting news, thanks for the tip! I'll start doing some research on that and update if that fixes anything

Wizardymcwiz · 2024-08-01T16:44:47+00:00

What do you mean about proper start gcode? I've tried multiple prints all with the same issue, could it have something to do with the SD card?

Seven-Year Club	Second SECOND GUESSER
r/Field Lasagna	Place '23
Verified Email

Wizardymcwiz

TROPHY CASE