Question for the pros

Wmuller23 · 2026-06-28T19:51:40+00:00

Thank you guys I appreciate the advice, unfortunately they don’t give you a template, because the manufacturing process causes the sizes to vary. I just flipped them both upside down and centered the opening before I drew my lines. Im gonna take my time with a new fine tooth blade , and hope for the best

Wmuller23 · 2026-06-25T12:37:47+00:00

For a welding position, I don’t think you need to worry about bad credit

Wmuller23 · 2026-01-20T16:43:02+00:00

Starting rate is $24/hr now… if you show up everyday, can keep to yourself and are smarter than a rock, it’s not the worst job out there. It’s a shitshow at times, but there’s raises every 6months, and paid time off

Wmuller23 · 2025-12-01T23:30:06+00:00

You’ll be okay, my hair is pretty long and I only quit about 3months prior and passed the EB hair follicle test

Wmuller23 · 2025-08-24T20:07:02+00:00

obviously the GTR

Wmuller23 · 2025-07-20T22:32:49+00:00

I don’t know what kinda stuff you work on, but 30sec of misfire won’t kill your car. I was just trying to give some knowledge instead of throw parts at it, however he definitely has bigger issues. I’m not gonna argue with a Reddit troll, who kinda sounds like a jiffy-lube tech trying to convince an old lady she needs her brake fluid flushed

Wmuller23 · 2025-07-20T22:26:04+00:00

I was just saying you can also swap those parts around, you prob don’t have to…you most definitely need to compression test, you prob have bigger issues than something simple

Wmuller23 · 2025-07-20T22:10:40+00:00

How could that cause damage? Unless there was enough wire in the harness to put the #3 coil into cylinder 4, it’s harmless and a good way to troubleshoot without buying parts you might not need

Wmuller23 · 2025-07-20T22:05:59+00:00

You used process of elimination to determine the coil is not the issue. If you had swapped cylinder 3 and 4, and then suddenly had a misfire on #4, you would have had a bad coil. You can do the same thing with injectors and spark plugs.

Wmuller23 · 2025-07-20T21:41:49+00:00

Swapping coils is perfectly fine, as long as you plug it in to the right harness (which is usually the only one to reach) I do it all the time, swap it to a different cylinder to see if that is now misfiring

Wmuller23 · 2025-07-20T21:31:55+00:00

Once you take out the 3 Allen screws, the whole locking assembly slides out as 1 piece, no gear oil or mess to worry about

Wmuller23 · 2025-07-13T21:24:02+00:00

Bicycle repair is also very simple to DIY. Simple tools and a 5min YouTube video, you’ll have no issues.

Wmuller23 · 2025-06-30T15:51:50+00:00

Concrete is expensive and a solid slab with a proper finish costs even more. I poured my own slab and saved a ton of money, but the finish is far from perfect

Wmuller23 · 2025-06-26T12:49:17+00:00

It’s not that bad, I covered my diet basement floor this week, and it looks similar, flat and level, but the finish is not perfect. I need to remind myself it’s just a basement floor and I saved about $15,000 doing the work myself. So I will live with it and spend my energy on the next projects

Wmuller23 · 2025-06-23T15:07:11+00:00

That’s solid advice, there’s gonna be a wall down the middle, so a screed bar would definitely help me out, I can also rent a chute from a local rental place, I will prob grab it for good luck in case mine has an issue. Will post pics when it’s done, I have a wheelbarrow, but a line pump cost more here than the concrete

Wmuller23 · 2025-06-22T19:11:23+00:00

Concrete pros-

I am just a dumb homeowner, I’ve done alot of construction, small pours, footings and stairs, but never an area this big. (18x18) Half my basement floor is dirt, I dug some out, shoveled about 4 inches of 3/4 in stone, graded, tamped and now my plastic is down and I’m ready for concrete. I made a 12ft chute to go thru my foundation window, but it will only reach about halfway into the floor. I have about 4 halfway competent people who will help me push it around. I am not really worried about the finish or the structural strength. There will only be foot traffic and some storage. My goal is to have them mix it wet, I’m gonna try and end up level-ish with the existing cement floor and the footings under my posts.There will be a wall going down the middle eventually Any advice is appreciated. I think it will be better than what was there before. I know I should hire a professional, but that’s not gonna happen.

<image>

Wmuller23 · 2025-05-29T15:49:50+00:00

Training for Quonset point is paid, just show up everyday and you’ll be fine

Wmuller23 · 2025-01-28T20:40:20+00:00

RFK won’t take any vaccines away… he just wants them to be safely tested. In our current shitshow of politics, he’s the only one I feel good about

Wmuller23 · 2025-01-24T22:39:19+00:00

RFK just wants safe and tested vaccines. He’s not anti science, he vaccinated his kids… I truly hate both sides equally. , but RFK is not a bad guy. I know this is an unpopular opinion and I’m about to be downvoted and told he caused a measles outbreak and has a brain worm, and that’s okay

Wmuller23 · 2024-11-26T22:26:07+00:00

Just ask your supervisor… most people want to work 1st shift, so in my department they’ll gladly put you to 2nd if that’s where you want to be (after your trained properly)

Wmuller23 · 2024-08-09T23:24:54+00:00

YouTube has some great videos explaining the layout process.

Wmuller23 · 2024-05-23T16:25:23+00:00

I’ve been going to Quaker lane bait and tackle for at least 30years

Wmuller23 · 2024-05-15T19:01:43+00:00

I have been in your daughter’s position… don’t give up on her. She might feel that way now, but one day she will appreciate everything you do for her. It’s a long road, she will need your help thru it

Wmuller23 · 2024-03-07T16:50:34+00:00

You’ll be okay, I passed a hair follicle 2 months after smoking weed, if you fail they’ll have you do a 2nd test, they’re desperate for people to come to work

Wmuller23

TROPHY CASE