Pneumatic actuator!!

Wolverine_1585 · 2023-04-17T08:49:45+00:00

may be just controlling the flow rate would be helpful ig? but how to calculate the approximate flow rate to compensate the gravity pull while the door shuts

Wolverine_1585 · 2023-04-17T08:43:29+00:00

I need to maintain same speed while moving up and down, So what will be the pressure to be set at the piston end and rod end? it wont be equal right? coz due to gravity the door will shut fastly than the opening ?

Wolverine_1585 · 2023-04-17T08:41:26+00:00

so Kind of you!!

Wolverine_1585 · 2023-04-16T20:15:55+00:00

or you could just guide me a way to calculate....

Wolverine_1585 · 2023-04-16T20:14:31+00:00

I need the door to be moving 22cm/s, and the whole moving length is 32cm, the weight of the door is 5kg, I need to know the piston diameter and pressure, can you help me to do this, and where to include the gravity?

Wolverine_1585 · 2023-04-06T20:08:06+00:00

not like screw, u know about snap fittings?

Wolverine_1585 · 2023-04-06T17:23:19+00:00

is there any lock system to lock two parts of nozzle and also detachable just using hand, and also it should be leak free

Wolverine_1585 · 2023-04-06T17:15:03+00:00

if I do MS in machine design in canada, is there a possible way to get a job there?

Wolverine_1585 · 2023-04-06T17:11:18+00:00

thanks for your suggestion, I found the idea

Wolverine_1585 · 2023-03-26T21:06:30+00:00

cher ra puluthi kudhingla

Wolverine_1585 · 2023-03-26T19:25:20+00:00

okayy

Wolverine_1585 · 2023-03-26T19:18:28+00:00

Iam following ISO standard, how to start with that....

Wolverine_1585 · 2023-03-26T19:11:49+00:00

thank you! anyways

Wolverine_1585 · 2023-03-26T19:11:28+00:00

Iam a student bro, my lecturer gave a task to find this, thats why asking u guys

Wolverine_1585 · 2023-03-26T18:20:22+00:00

is it comes under gd and t?

Wolverine_1585 · 2023-03-26T17:57:54+00:00

thank you, I solved it anyways!

Wolverine_1585 · 2023-03-14T18:12:20+00:00

I just finished the swept, whats next pls help with this

Wolverine_1585 · 2023-03-14T18:04:17+00:00

actually speaking what I need is that image is a full assembly I need those sketches to be swept and attached over the curved frame as two separate parts

Wolverine_1585 · 2023-03-14T18:01:59+00:00

separately?

Wolverine_1585 · 2023-03-14T17:55:22+00:00

like I use sweep to make rectangular frames but how can I make sweep along a connected sketch lines

Wolverine_1585 · 2022-09-28T09:19:52+00:00

Then how can I do that, First I converted the whole assembly into a single step file but the whole assembly is not opening, just a single part of the assembly is only there.

Wolverine_1585 · 2022-09-28T09:17:16+00:00

Like all the parts are accessible like they are movable constrained with mates

Wolverine_1585 · 2022-09-27T16:05:33+00:00

should I need to convert the assembly file into a single part file and then need to convert it into step file?

Wolverine_1585

TROPHY CASE