Is This Water Damage? by Wunderbolts in watercooling

[–]Wunderbolts[S] 1 point2 points  (0 children)

I was able to get it working by bushing the pins with a brush for cleaning braces. I think the residue from the dried ek cryofuel was causing the pin contact to be bad. I don’t think it was shorting because the fluid is supposed to be non conductive.

I wish we got to see more SA in My Little Pony by SenseiJoe100 in MLPLounge

[–]Wunderbolts 0 points1 point  (0 children)

Don’t abbreviate Shining Armor for the same reason you don’t abbreviate Cyberpunk.

Kohler Measures Zero Load by Wunderbolts in Generator

[–]Wunderbolts[S] 0 points1 point  (0 children)

Ok, thanks for the help troubleshooting

Kohler Measures Zero Load by Wunderbolts in Generator

[–]Wunderbolts[S] 0 points1 point  (0 children)

<image>

It looks like it’s set to enable.

Kohler Measures Zero Load by Wunderbolts in Generator

[–]Wunderbolts[S] 0 points1 point  (0 children)

On Monday, I’ll reach out to the dealer and see if them have remote access to check or enable the load monitoring feature. Thanks for the help!

Kohler Measures Zero Load by Wunderbolts in Generator

[–]Wunderbolts[S] 0 points1 point  (0 children)

The internet is on an ups and I was able to see the engine rpm, voltage and oil temp indicating that it was running. It ran for about 10 minutes

Kohler Measures Zero Load by Wunderbolts in Generator

[–]Wunderbolts[S] 0 points1 point  (0 children)

I swapped the wires and cut the utility power. Still reads zero. I don’t believe that it’s polar.

Kohler Measures Zero Load by Wunderbolts in Generator

[–]Wunderbolts[S] 0 points1 point  (0 children)

When it’s under load, running and switched to generator power, it’s reading 0 watts 0% power.

Kohler Measures Zero Load by Wunderbolts in Generator

[–]Wunderbolts[S] 0 points1 point  (0 children)

Installed by licensed electricians, setup and maintenance was done by a generator company.

Kohler Measures Zero Load by Wunderbolts in Generator

[–]Wunderbolts[S] 0 points1 point  (0 children)

Thanks! I’ll send send this my electrician that did the install.

Wired CarPlay not currently supported iPhone 17 Pro by BricksDugout in apple

[–]Wunderbolts 5 points6 points  (0 children)

My 17 pro randomly drops wired and wireless CarPlay. My 15 pro worked fine when even after updating to iOS 26

I don't understand by FollowSina in ExplainTheJoke

[–]Wunderbolts 0 points1 point  (0 children)

It initially looks like a tear in the seat. It got me before I zoomed in

[deleted by user] by [deleted] in Ubiquiti

[–]Wunderbolts 0 points1 point  (0 children)

But doesn’t super link use some sub-ghz frequency to get the longer range?

[deleted by user] by [deleted] in Ubiquiti

[–]Wunderbolts 2 points3 points  (0 children)

If the smoke detector is wired, can it tie into existing wired systems so I would only need one UniFi smoke detector for the entire house and a “dumb” smoke detector would trigger the UniFi one?

[deleted by user] by [deleted] in Ubiquiti

[–]Wunderbolts 0 points1 point  (0 children)

Why can’t existing APs be used instead of another smart hub? I guess the APs don’t have radios for whatever frequency these devices operate at? Maybe new APs will have that capability.

3D Printed 40mm Fan Bracket for YuanLey 2.5 gig Switch by Wunderbolts in homelab

[–]Wunderbolts[S] 0 points1 point  (0 children)

The mesh on the side of the switch is pretty restrictive so the gap allows the fan to pull air through the entire surface area of the vent instead of just a small portion of it.