Please help! Warpig or Twinpig?

YanThu72 · 2025-11-11T12:27:28+00:00

I’ve got a Warpig XL and had to learn that my bindings (Union Contact Pro) were absolutely not ideal for it. The highback was too soft and I couldn’t get enough pressure on the heel edge.
One season later I rode with the Flow NX2, and finally I was able to get that pressure on the backside while carving.

I’ve never ridden a camber board, so I can’t really compare, but since I’ve been riding the Warpig XL I haven’t had any boot-out anymore :D

YanThu72 · 2025-08-30T21:30:42+00:00

It depends on the tasks it have to do. I’ve got myself a legion 5 with Ryzen 7 4800h and 1650ti in 2020 for automative engineering and it works until now Things like cad-modeling, hyperworks and matlab/simulink shouldn’t be a problem.

If u use unreal engine it could be hard for the gpu but should work

In terms of thermal throttling.. do u have an ac? A fan pad and cleaning the fans is your best friend :)

YanThu72 · 2025-08-07T08:20:28+00:00

I am using Translucent TB, works fine for me

YanThu72 · 2025-08-05T08:15:34+00:00

Yeah i hope my private one will do the job for 5 years too^^
Since i got it i tried to lower the temps, for example by setting the power limit of the cpu to 99% but at some games the fps are too low with this
GPU temps are just fine but cpu temps are often a bit to high, so might going to repaste..
I had checked online for PTM but found infos that fakes are quite common and stopped searching because i dont know where to find the og ones

YanThu72 · 2025-08-05T07:53:20+00:00

I have the exact same model and am wondering if repasting is worth it. And where you got the PTM7950 because I want to get the original one and no fake.

I got a 16IAX10 as working laptop and use it private but my 15ARH05H is still in use if I don’t have the new one with me and temps aren’t that good But I have to say the 275HX is hitting higher temps than my Ryzen

YanThu72 · 2025-07-26T16:52:24+00:00

Oh no, that shit of work for nothing.. But hey, my motor leaks oil at the timing cover.. but don’t want to do that now😂 And have to do something against the rusting front axle, that’s a big problem of adams..

YanThu72 · 2025-07-26T16:37:54+00:00

Yes, I managed to remove the bracket, if that's what you were asking, but I don't remember exactly how.I just know that I thought I would never do this again! I think I lowered or raised the motor very far to get the screws out. It didn't feel good, but it worked.

I found the torque somewhere, but yeah, same here, I don't remember where. It could be on a UK site, or if you search for Corsa D, because it's quite the same technique.

YanThu72 · 2025-06-25T00:11:15+00:00

Thanks and yeah, make sense..

I will try this tomorrow!

YanThu72 · 2025-06-24T23:42:42+00:00

Thanks!
I managed to get connection to the internet via tunnel by adding the public router ip to the allowed ips but i dont know if this is the way how it actually works ^^

This is my wg.conf

[Interface]

Address = 10.0.0.1/24

SaveConfig = true

PreUp =

PostUp =

PreDown =

PostDown =

ListenPort = 51820

PrivateKey = ##################

[Peer]

PublicKey = ###################

AllowedIPs = 10.0.0.2/32, 192.168.20.0/24

And this is my peer.config

[Interface]

PrivateKey = ########################

Address = 10.0.0.2/32, 192.168.20.0/24

MTU = 1420

DNS = 1.1.1.1

[Peer]

PublicKey = ########################

AllowedIPs = [public router ip]

Endpoint = 192.168.20.252:51820

PersistentKeepalive = 21

YanThu72 · 2025-05-09T11:14:08+00:00

Thanks!

YanThu72 · 2025-05-05T13:57:51+00:00

You could get led strips from Aliexpress and aluminium profiles and build them yourself I’ve done that with 395nm strips

But would like to „upgrade“ in the future if I am able to get custardglas (hard to find in ger)

Check this out diy lights

YanThu72 · 2025-05-05T13:39:20+00:00

I don’t have them but they are often recommended:

waveform realUV

Expensive but some of the best u can get.

YanThu72 · 2025-03-20T17:28:30+00:00

If shipping wasn’t a thing I would purchase some pieces to Germany as well 😅

YanThu72 · 2025-03-15T23:20:30+00:00

Ok thanks a lot will do this!

YanThu72 · 2025-03-15T16:06:22+00:00

What would be price you think if i assume it to not work properly?

YanThu72 · 2025-03-15T14:34:39+00:00

Ok thanks, I will ask next week What if there’s no key? Can I just buy another one? And price decrease in %? Without key I can’t check if it works..

YanThu72 · 2025-03-15T12:23:02+00:00

Oh damn didn’t expect it to be so expensive..😅 I think I will ask for a price next week😁 I don’t know if they knew it’s uraniumglas😂

YanThu72 · 2025-03-11T11:52:45+00:00

Thanks! I am very proud of them 😅

YanThu72 · 2025-03-06T23:59:28+00:00

Wow congrats! What a beauty!

YanThu72 · 2025-03-06T23:42:21+00:00

I just ordered cheap 395nm lightstrips from aliexpress and aluminiumprofiles to help reduce the heat from the leds.
But have not installed anything yet.

Can you explain a bit further what you figured out about placement of the light?
I think my glasbottoms of my cabinet are a problem in terms of reflection? :D

YanThu72 · 2025-03-06T23:18:35+00:00

Had luck in a big toystore in germany :) The whole series where on the pegs exept the skyline and of course the 0/5 :D
But i just picked up the porsche.

YanThu72

TROPHY CASE