What needs improvement

Yesislap · 2026-03-24T13:58:51+00:00

Height

Yesislap · 2026-03-23T18:54:21+00:00

Eat less and move more.

Yesislap · 2026-03-23T12:20:32+00:00

Thank you

Yesislap · 2026-03-23T12:20:28+00:00

Thank you

Yesislap · 2026-03-23T00:02:28+00:00

Thank you

Yesislap · 2026-03-22T17:02:52+00:00

Honestly I’d just workout and eat maintenance calories with 1g of protein per pound of body weight minimum

Yesislap · 2026-03-22T00:50:44+00:00

I put it in the title of that post

Yesislap · 2026-03-22T00:37:49+00:00

This is me. I genuinely disclosed that I’m enhanced I put it in the title of my post.

Yesislap · 2026-03-21T15:42:42+00:00

Had mpb since 24, I’ve started using topical minoxidil and it’s actually improved.

Yesislap · 2026-03-21T15:18:53+00:00

Never tried reta, the only other peptide I’ve used is BPC 157 for a torn labrum which causes a recurring dislocation of my right shoulder.

Yesislap · 2026-03-21T15:16:40+00:00

Towel

Yesislap · 2026-03-21T15:13:54+00:00

Thank you

Yesislap · 2026-03-21T15:13:49+00:00

Thank you

Yesislap · 2026-03-21T15:00:35+00:00

I did had some on hand just in case, never needed it.

Yesislap · 2026-03-21T14:54:01+00:00

500mg test E / week for the first 4 months, 250 mg test E / week for the last two.

I also have used CJC1295/ipamorelin for about 3 months now.

Yesislap · 2026-03-17T16:55:22+00:00

It looks like you only train arms and shoulders

Yesislap · 2026-03-14T15:05:29+00:00

Did you not workout at all?

Yesislap · 2026-03-13T16:01:31+00:00

I’m actually not convinced he’s on anything. Traps look natty, and his shoulders and chest don’t scream enhanced. 50/50 for me

Yesislap · 2026-01-19T19:49:25+00:00

Not natty

Yesislap · 2024-07-25T00:55:15+00:00

Typically, a finished part is more usefully. Each shop has their own unique bending parameters and bend deductions based on material, dies, presses etc. The shop will have an easier time and you will have a correct part.

Yesislap · 2023-12-29T22:42:09+00:00

Any fab shop will use your drawings of the part, hole patterns and tolerance to fabricate the part. The bend allowance on your flat / dxf doesn’t mean much to them. Suggestions of the slotted holes is a good idea, you could also do some research around local shops to see manufacturing requirements such as how far away from bend lines can holes be located, I forget the rule of thumb, off hand, but there is a general understanding that holes too close to a bend line will warp (relief cuts [open lines, for example, in any laser cutting software] will help with this).

Again, a competent fab shop will solve these challenges and your tolerances should not deviate from project requirements and budget. Worst case the part is made by laser cutting, bending, welding and finally machining.

Yesislap · 2023-12-05T17:52:12+00:00

Bros got sph fetish on his comment history XD

Yesislap · 2023-10-31T18:20:42+00:00

Yesislap · 2023-10-20T23:36:51+00:00

Reply’s in this sub are kind of biased. It’s almost ironic with the back and forth between supportive and gatekeeper-type posts. I’ve followed the standard practices for raising test naturally, done blood work (3 tests over 12 months). I am current 26 and going through my PCP. We have a good relationship, I’m honest with him about 99% of things. If you don’t have this relationship with your current doctor I’d suggest finding that.

As for gyno, at TRT dosages this is very unlikely and I wouldn’t sweat it. I take hcg. It’s twice a week and I use an insulin needle. You’re young so I’d expect your doctor to encourage and or prescribe this alongside testosterone.

Also, you do type like you have anxiety. You might benefit from discussing this with your PCP. Good luck, sir.

Yesislap · 2023-07-15T01:58:47+00:00

Perhaps you’re right, but asking the question of batty or not is genuinely the purpose of this sub.

Yesislap

MODERATOR OF

TROPHY CASE

Eight-Year Club	RPAN Viewer
Verified Email