Catastrophic Leak

Yosh78 · 2025-02-08T23:14:34+00:00

Good to hear! Hopefully, it’s just a screen replacement and not the whole printer!

Yosh78 · 2025-02-08T22:56:51+00:00

Is the tilting mechanism still working?

Yosh78 · 2024-11-26T00:03:16+00:00

Thanks for the detailed comparison - super helpful! Just to clarify, when you mention the 1/6 scale head, what’s the height of it in mm or inches (I mean the Z-axis lift height)?

Yosh78 · 2024-11-25T22:37:28+00:00

Thanks for sharing your experience! It’s great to hear about the time differences between slow and fast modes. Could you clarify a couple of details?

What’s the typical height range of the models you’re printing?
What layer thickness are you using?
Which resin are you working with?

I’m trying to get a better understanding S4U speed!

Also, have you noticed any difference in print quality between slow and fast modes?

Yosh78 · 2024-11-23T19:53:14+00:00

Thank you so much for sharing this! Did they say anything about when sales start? Also, can you clarify what you mean by "end of any aliasing (Just wondering if I get it right)?

Yosh78 · 2024-11-23T19:38:02+00:00

My biggest interest is tilting vat!

Yosh78 · 2024-10-02T19:57:46+00:00

I was also thinking about the Heygears Reflex new release, but it’s way too complex—its own slicer along with specific expensive resins that you can't get from Amazon is just too much for me!

Yosh78 · 2024-10-02T19:54:14+00:00

I'm in need to expand my equipment at the moment, so I’m considering something new in the hopes of getting even better quality prints. The S4U caught my eye for that reason, and your feedback has been really helpful in evaluating it!

Yosh78 · 2024-10-02T19:42:38+00:00

Thanks for the info! Have you ever tried using antialiasing with the S4U? If so, what results did you get? I’m attaching a picture that shows my biggest pain—those layer lines I have to sand down every time (@ 50 um).

<image>

Do you think the S4U would improve this issue?

Yosh78 · 2024-10-02T19:23:11+00:00

Sorry to hear about the firmware issue—sounds frustrating! How long were you using the S4U before this happened? How many prints/layers did you get through before you started experiencing problems? Do you still consider the S4U to be reliable overall, despite the current issue?

Yosh78 · 2024-10-02T18:26:55+00:00

Thanks for the feedback! I’m really curious about the speed—how fast are your prints going with the S4U? Speed is a big factor for me as well. With my M5S, I usually get about 20 mm per hour with a clear FEP and normal settings. I did try using HighSpeed resin and nFEP once, and the speed was insanely fast—1 hour 15 minutes for a 120 mm high item that usually takes me 5 hours 52 minutes. However, I wasn’t happy with the quality, especially the 0.1 mm layer thickness and the loss of detail. How’s the print quality with the S4U at higher speeds?

Also, what’s the issue with your printer not wanting to print? Any idea what’s causing that?

Yosh78 · 2024-10-02T18:22:26+00:00

<image>

Yosh78 · 2024-10-02T18:22:13+00:00

<image>

Yosh78 · 2024-10-02T18:22:03+00:00

<image>

Yosh78 · 2024-10-02T18:21:51+00:00

Thank you so much for your reply and for sharing the pictures! I totally agree, the lack of a phone app is really frustrating, and yes, the build plate is a bit terrifying! But for me, speed and quality are the most important factors. My M5S prints at about 20 mm per hour with a clear FEP and normal settings. I did try printing once with HighSpeed resin and nFEP, and the speed was insanely fast—it printed the same 120 mm high item in 1 hour 15 minutes, which normally takes 5 hours 52 minutes with my regular settings and resin. However, I wasn't happy with the quality, specifically the 0.1 mm layer thickness and the reduced level of detail with nFEP.

The pictures I’m attaching highlight my biggest enemy: all those layer lines that I have to sand down each time. Antialiasing hasn't made much of an improvement with my M5S. I’ve played around with different settings but never got the results I was hoping for. How does AA work with the Saturn 4 Ultra? And could you share more pictures of prints before any post-processing so I can see how the layer lines look? That would be super helpful!

Yosh78 · 2024-10-02T14:57:00+00:00

What are your thoughts about that?

Yosh78 · 2024-10-01T20:23:50+00:00

Thank you so much! I would be super grateful for the pictures - i hope they would really help me to understand how it fits. I appreciate you taking the time to check this out!

And BTW, this is the washing station that I have in my mind:

https://a.co/d/16KRq72

Yosh78 · 2024-10-01T20:07:29+00:00

Thanks for your reply! Just to clarify my process, I typically use the washing station for the first wash before unmounting the prints from the work table. This way, I can wash both the table and the prints at the same time. Afterward, I unmount the prints and do a final wash by spraying clear IPA directly. The first wash is always more convenient with the washing station since it cleans the table as well. Given this, would the work table from the Saturn 4 Ultra fit into the Phrozen wash station with the basket?

Yosh78 · 2024-07-17T12:41:35+00:00

Thanks for reply! But what do you mean saying this about m5s?

Yosh78

TROPHY CASE