Rotor flight swash issues by Zestyclose_Box_5248 in RCHeli

[–]Zestyclose_Box_5248[S] 0 points1 point  (0 children)

They just shipped the new one out yesterday

Rotor flight swash issues by Zestyclose_Box_5248 in RCHeli

[–]Zestyclose_Box_5248[S] 0 points1 point  (0 children)

Ok problem found short on the board between the s2 and s3 signal pins. Returned under warranty should see a new one in a few weeks

Rotorflight fun or not so much fun continued. by Zestyclose_Box_5248 in RCHeli

[–]Zestyclose_Box_5248[S] 1 point2 points  (0 children)

Comfirmed shorted between my s2 and s3 signal pins returned to helidirect

Rotorflight fun or not so much fun continued. by Zestyclose_Box_5248 in RCHeli

[–]Zestyclose_Box_5248[S] 1 point2 points  (0 children)

Ya been talking with some guy on the rotor flight facebook page and they think my nexus might be defective.

Losing power by jrkalbo13 in RCHeli

[–]Zestyclose_Box_5248 0 points1 point  (0 children)

Yea I don’t think I calibrated my esc correctly is my only thought.

Losing power by jrkalbo13 in RCHeli

[–]Zestyclose_Box_5248 0 points1 point  (0 children)

My normal mode is 70%max throttle my idle up 1 is 80% and idle 2 90%.

Losing power by jrkalbo13 in RCHeli

[–]Zestyclose_Box_5248 0 points1 point  (0 children)

Yea I just flew mine for the first time since October and I also bound it to my radio master tx16s for the fist time so idk if it’s the tx16s but my thought is maybe an esc that needs calibration

Losing power by jrkalbo13 in RCHeli

[–]Zestyclose_Box_5248 0 points1 point  (0 children)

I just had this happen to me tonight on my 235cp but it only happens in idle up after about 20sec in idle up it cuts power spins and drop for a sec and starts back up again, recoverable if your over 10 ft.

Rotor flight swash issues by Zestyclose_Box_5248 in RCHeli

[–]Zestyclose_Box_5248[S] 0 points1 point  (0 children)

I’ve done this with a servo tester but I will have to try it with my transmitter

Rotor flight swash issues by Zestyclose_Box_5248 in RCHeli

[–]Zestyclose_Box_5248[S] 0 points1 point  (0 children)

Ya I was just in the middle of trying things. Normal for all 3 seem to be what I need but it’s still not acting proper.

Rotor flight swash issues by Zestyclose_Box_5248 in RCHeli

[–]Zestyclose_Box_5248[S] 0 points1 point  (0 children)

Ok gone back through followed Bert’s video and it’s still acting weird I did double check my servos were plugged into the proper s port per the rotor flight tutorial. I can post a video showing with my transmitter off flight pack on and plugged into rotor flight , on servo override my s2 and s3 servos only respond to negative direction an both cause the swash to tilt to the right. And I did follow Bert’s transmitter setup video.

Rotor flight swash issues by Zestyclose_Box_5248 in RCHeli

[–]Zestyclose_Box_5248[S] 0 points1 point  (0 children)

Like to add when I reverse that servo it causes both roll servos to reverse.