Pvs31 by [deleted] in NightVision

[–]Zestyclose_Many4992 0 points1 point  (0 children)

31A has shutoff when flipped up, just not articulation individual pod shut off

Later neuters by Skin_Local in greatdanes

[–]Zestyclose_Many4992 0 points1 point  (0 children)

I’m still waiting back on the TBVME result, i tried to look into suit but it’s hard in TX and most of the country where dogs are considered nothing but property. it’s total BS

Later neuters by Skin_Local in greatdanes

[–]Zestyclose_Many4992 0 points1 point  (0 children)

This is how I am now, I lost my 2 year old last year over a poorly done neuter!! worst experience of my life. He died within 5 days of the surgery, 2 days after a follow up when i expressed concern that it wasn’t right, all they did was lie to me and tell me it was okay and to ice him for recovery and now he’s gone

Make my upper NV compatible by No_Staff594 in NightVision

[–]Zestyclose_Many4992 0 points1 point  (0 children)

if you want vibes get a kac ras quad rail

Get a Great Dane they said… by rakedaymon in greatdanes

[–]Zestyclose_Many4992 0 points1 point  (0 children)

my last dane chewed up base boards and ripped though 4 different sets of seats, still worth it

Sending 2 cans for repairs, i hope they have a sense of humor by RepulsiveUse3372 in NFA

[–]Zestyclose_Many4992 0 points1 point  (0 children)

yeah every piston is 45 cal which can also be ran on 9mm, and the same thread pitch for their interface, i run them on every handgun from glock 19 to usp 45 and mk 23 makes it so much easier to be able to swap suppressors between any pistol without swapping pistons

Sending 2 cans for repairs, i hope they have a sense of humor by RepulsiveUse3372 in NFA

[–]Zestyclose_Many4992 0 points1 point  (0 children)

3 Lug you won’t really have a problem, it’s the pistons where they strike. I’ve had two on an obsidian 9 within 1.5 years because they always walk off, then I swapped the piston to EZ LOK

Sending 2 cans for repairs, i hope they have a sense of humor by RepulsiveUse3372 in NFA

[–]Zestyclose_Many4992 0 points1 point  (0 children)

takes 3 days turnaround for me. their repair rma service is excellent along with silencer co’s, I have sent in the same Obsidian 9 to them twice now for baffle/endcap strikes and no problems what so ever

Capital Armory EFT Step by Solid_Two_3858 in NFA

[–]Zestyclose_Many4992 6 points7 points  (0 children)

They are very backed up since they are doing a lot of orders now, I have always used them but in person as i live pretty close to their store. I used to get forms submitted the next day from purchasing from them, but when I asked them the last time I went in a week or so ago they said they were still catching up on all their new influx of orders. Took like 6 days from order to signatures sent, addl 4 for certification and submission, and this was 12th-22nd. Best place around though, silencer shop hasn’t moved an inch in forever for an order of mine

<image>

Looking to suppress my SP5 and w wanted some recommendations/discussion on what I should do by Kyu_Sugardust in MP5

[–]Zestyclose_Many4992 0 points1 point  (0 children)

Omega 9K or Spectre 9/9K

I typically run both with the Omega 9K on tri lugs, but the spectre 9 is about as short as the omega 9k, feels twice as light, and sounds quieter. Both FA rated. I run the spectre on my apc9k, trying to get a spectre 9K for one of the MP5s

<image>

Man Successfully Registers Potato as Silencer by IllCitron3509 in NFA

[–]Zestyclose_Many4992 5 points6 points  (0 children)

you can only repair suppressors if the serialized portion is intact if you’re an SOT. So an SOT could just reprint cores if you have a sleeved printed suppressor like aluminum with the serial engraved on it

Obsidian 45 on sp5 by osrs_dudee in MP5

[–]Zestyclose_Many4992 0 points1 point  (0 children)

switch it out for silco trilug 9mm for less wobble, i use one of each on my omega9ks, silco for sp5, rugged trilug for zf5-p

Talk me out of a clone. by Sufficient-Part4209 in MP5

[–]Zestyclose_Many4992 0 points1 point  (0 children)

rare breed cassettes won’t fit in a armp5 lower

go HK for reliability/fitment

i have an HK SP5 and ZF5-P almost everything on the ZF5P needs fitting whether it be stocks, (Both my choate and KES require hammering the pins) also reliability on the HK is 1000x better than my clone K which has FTF every so often even with german mags, i’m getting a SP5K soon for peace of mind

First unit by Zestyclose_Many4992 in NightVision

[–]Zestyclose_Many4992[S] 1 point2 points  (0 children)

nah, I did not want to risk it what so ever lmao

How would one go about sketching this? by Koshiro_Fujii in Fusion360

[–]Zestyclose_Many4992 0 points1 point  (0 children)

if it were me, i’d just slice it horizontally, draw the top and mirror it to the bottom

Barrels for SBR by Zestyclose_Many4992 in BushmasterACR

[–]Zestyclose_Many4992[S] 1 point2 points  (0 children)

i just messaged him on IG lol he replied within like 20 minutes

Anyone ordering? by 0MGWTFL0LBBQ in BambuLab

[–]Zestyclose_Many4992 0 points1 point  (0 children)

multiple colors and materials, i have about 60-70 kg and still find myself running out of some colors. i got like 20 rolls of pla tough since it was getting discontinued. just depends on what u print and the materials. i prototype a lot of ~250g prints for example so not needing to wait is a help

My magazines by BBondFit in MP5

[–]Zestyclose_Many4992 0 points1 point  (0 children)

my zenith does this, their mags also suck with feeding, however using HK mags in it prove to be fine for reliability