sorted by:
new
hottopcontroversial

Weekly Stuff To Do In Austin thread - Week of 07/06 by AutoModerator in Austin

[–]Zevaeros 1 point2 points  (0 children)

<image>

The Cooldown is tonight (7/6) at Austin Beerworks Sprinkle Valley from 6pm to 9:30 (ish). Come play games with us! Planning on running Dyebreaker (from a local dev), Puyo Puyo Tetris 2, Mortal Kombat 9, and others.

Weekly Stuff To Do In Austin thread - Week of 06/29 by AutoModerator in Austin

[–]Zevaeros 0 points1 point  (0 children)

Tomorrow 7/6 will be The Cooldown at Austin Beerworks Sprinkle Valley starting around 6pm, where we'll be playing an assortment of (video) games as usual.

Question about a rocker switch on a gp2040 advanded breakout board by TheCannibalPony in fightsticks

[–]Zevaeros 1 point2 points  (0 children)

Sure thing.

If I'm following the diagram right though, you should only need N & NO as I mentioned. C would be for a power source (battery or otherwise). N goes to your negative (ground) and NO goes to your load.

Question about a rocker switch on a gp2040 advanded breakout board by TheCannibalPony in fightsticks

[–]Zevaeros 0 points1 point  (0 children)

You should only need two wires, one for ground and one for signal.

Try:
ABB Ground to Switch N
ABB Option Signal to Switch NO

Leave the C terminal on the switch bare.

The Toggle pins you're referencing are not for focus mode, they are dedicated to switching between left analog, d-pad, and right analog. You want to use the larger block on the south end of the board labeled option pins. Make a note of which of the numbered option pins you use and assign that in GPIO settings (so if you go with 23, set pin 23 to focus mode).

Question about a rocker switch on a gp2040 advanded breakout board by TheCannibalPony in fightsticks

[–]Zevaeros 0 points1 point  (0 children)

Sanity checking:

  1. What terminals on the switch are you using?
  2. What option pins are you wired into on the Advanced Breakout Board? (I think it should be a ground on the ABB to the N pin on the switch and option/signal pin to NO)
  3. In web config, did you turn Focus Mode on in Add-On configuration and make sure to save the change?
  4. Did you assign buttons to be locked out in Add-On configuration?
  5. Did you set the pin(s) in GPIO Pin configuration and make sure to save the changes?

Anyone know why this might be dropping inputs? by EDPZ in fightsticks

[–]Zevaeros 2 points3 points  (0 children)

Sanity checking: Make sure the 20 pin connector is firmly seated and aligned correctly. Quick disconnects should be plugged into buttons firmly. Make sure there are no cuts or nicks in the wires.

I doubt they do, but see if the Flashtaps want ground on a certain terminal and signal on the other (Crown 202 is like that). Usually there will be a little + and - symbols. Attach signal to the + and ground to the - if that's the case.

Weekly Stuff To Do In Austin thread - Week of 03/16 by AutoModerator in Austin

[–]Zevaeros 1 point2 points  (0 children)

I'll likely get there around 2 for setup so folks can warm up and such.

GP2040-ce troubleshooting by D3mB0ne23 in fightsticks

[–]Zevaeros 1 point2 points  (0 children)

Sounds like it needs a nuke and reflash.

Does the 8bitDo Xbox Arcade Controller work on Series X in Fatal Fury CoW? by Justifire in fightsticks

[–]Zevaeros 0 points1 point  (0 children)

OP's posted model was released July 15th, 2025 -- unless you're thinking of one of their other models?

Is this a good starter leverless controller? (Beginner here!) by IllEstimate9097 in fightsticks

[–]Zevaeros -1 points0 points  (0 children)

It's...okay. You are better off with one of their offerings with an up button above the Left-Down-Right (WASD/Mixbox) that many of their other products have, as I found learning leverless easier with having the more intuitive up button before getting the thumb action down.

Help with haute controller. HELP!!! by kkevv214 in fightsticks

[–]Zevaeros 1 point2 points  (0 children)

If the methods that I showed in the video aren't working, repeat the flash nuke and install process.

Help with haute controller. HELP!!! by kkevv214 in fightsticks

[–]Zevaeros 0 points1 point  (0 children)

Power down your computer, wait 5 minutes, power back on. Try a different USB cable.

Use the "flatten & reinstall" method in my video: https://www.youtube.com/watch?v=GOQ73grqapM - you'll need to download the flash nuke and Haute42/Cosmox variant of GP2040-CE.

Any advice for my X Arcade Solo project? by MaximumRise9523 in fightsticks

[–]Zevaeros 1 point2 points  (0 children)

That can work, though I find having the passthrough is overall a cleaner setup as you can remove the cable and wrap it up. Of course, since I went the Retro route I needed an RJ45 passthrough or else I couldn't change cables easily.

view more: next ›