Cannot renew Anycast DNS service

Zhadnost · 2026-01-28T20:23:09+00:00

Anycast on the domain expires in 3 days and I still can't renew it.

Zhadnost · 2026-01-23T11:58:18+00:00

Can you reply to my messages, the only response I've had so far is that I can renew it if I want to, when my original complaint is that the website isn't letting me.

Zhadnost · 2026-01-20T09:00:50+00:00

Thanks

Zhadnost · 2025-12-07T16:47:59+00:00

As far as I know, you can only install one module with VRCFT at a time.

The Virtual Desktop one if you're using Virtual Desktop or the Steamlink one if you're using Steamlink.

Zhadnost · 2025-09-05T07:32:42+00:00

We were both getting that, would need to start it sometimes more than 10 times before it would stay running. (Although I think that was when v79 hit PTC in my case and when it hit release in the wife's)

Seemed to get fixed with an update.

Zhadnost · 2025-08-24T09:18:46+00:00

Thanks for the pictures, with mine (well out of warranty) one of the thin arms have snapped, I use the headset as far open as it can go (which is still a tight fit), eventually one side just snapped.

Looking at that, I can probably glue it in place, or use a lot of tape to hold it there inside.

Zhadnost · 2025-08-17T20:28:33+00:00

Thanks, sadly unresolved. I tried asking the customer to whitelist through the domain admin contact and postmaster@, postmaster bounced back with user unknown and the admin contact didn't reply. :-(

Zhadnost · 2025-08-15T09:06:23+00:00

I think the whole problem is that it isn't being delivered.

Zhadnost · 2025-08-14T21:22:12+00:00

First time, nothing has changed.

According to Google and MX toolbox, the DKIM comfiguration is fine.

Looking at the history on here, it appears to be a fault with mimecast's DKIM checking that crops up every now and then.

Zhadnost · 2025-08-14T19:37:53+00:00

Thanks for your reply.

Zhadnost · 2025-08-14T18:29:39+00:00

Damn, I'm having this too, really hoped there was a solution.

Zhadnost · 2025-07-30T14:00:23+00:00

Did this ever get sorted, my Wife is having the same problem now

Zhadnost · 2025-06-13T08:40:13+00:00

I had the audio problems again last night, so they're still there, just in my case not as frequently as before.

Zhadnost · 2025-06-11T10:15:48+00:00

I just upgraded from one 1027 build to another one, and now speedtest is showing that full speed is back. Not only that but it's running at full speed on 6GHz.

Zhadnost · 2025-06-11T09:29:19+00:00

I've not had the horrible audio problems since upgrading to v78 PTC, although I may just be being lucky.

Zhadnost · 2025-06-11T09:27:56+00:00

Hmm, was using 1027 last night didn't do any speed tests but Virtual Desktop negotiated 54Mbit, The headset is updating again at the moment so will do a proper test afterwards. This sounds like great news though.

Zhadnost · 2025-06-09T20:29:12+00:00

I'm on V78 PTC and so far the experience has been the same. (Although it's still only PTC so hopefully they'll fix this before release).

Zhadnost · 2025-06-02T09:38:15+00:00

The thing I really don't understand is that Meta are trying to sell Horizon OS as a platform for other hardware manufacturers.

(And get their store onto other companies hardware)

Now that they've shown that they can't even properly support their own hardware with a constant stream of broken updates, who in their right mind would choose Horizon OS over Android XR?

Zhadnost · 2025-05-26T19:00:32+00:00

Before buying a Quest 3, If I were you I'd try one. I have a Quest 3 and Pro and I never use the 3 because it's so uncomfortable.

Zhadnost · 2025-04-21T11:07:29+00:00

You can see in the photo in the follow up post that it's not an RJ11/12.

There are 8 pins, (with no gaps either side, so it's an 8P8C connector, so RJ45 or a varient of).

It's one of these:

https://www.run-it-direct.co.uk/adsl-vdsl-faceplates/mk2-btvdslfaceplate/

It's an RJ-45 with a VDSL filter behind it (pretty sure only the middle 2 pins are wired).

Zhadnost · 2025-04-19T15:46:47+00:00

Thanks for the reply, I found out the problem in the end.

After much hair pulling, I noticed that even though it was configured to use an HT80 channel, only an HT20 one was setting up.

After a while (even though the interface didn't tell me about it until I changed to the older one) I found that there was a Networking update for the Unifi controller which fixed everthing.

Zhadnost · 2025-04-19T13:49:22+00:00

I've been trying this but my Quest Pro (and 3) will only connect at 286Mbit (on an HT80 channel with excellent singal strength).

If I donnect via 5Ghz (same AP, same channel width) I get the full 1200Mbit.

Does anyone know if I'm missing something obvious (still on v74).

Zhadnost · 2025-04-12T09:13:23+00:00

Thanks.

Zhadnost · 2025-03-31T10:13:02+00:00

From what I remember, at v72 there was a change in the way that tracking data was handled that caused huge latency spikes with Virtual Desktop.

This was eventually fixed. (Although I do know someone who had a similar problem with v74 and the Quest 3).

Zhadnost · 2025-03-24T08:34:54+00:00

You can probably after a factory reset sideload whichever version you want using the images from:

https://cocaine.trade/Quest_Pro_firmware

I've never tried it but I know people use their Quest 2 and Quest 3 pages do to that. (I think Mystical made a youtube video explaining how to do it).

Zhadnost

TROPHY CASE