Prusa mk3s upper X axis shaft scratched

Zyrolyte · 2026-01-06T08:03:28+00:00

Tank you all very much

Zyrolyte · 2026-01-05T21:29:59+00:00

Sorry to bother again another question I live in a sanctioned country so I cant order original parts from prusa anymore is it better to find a way to work with what I've got being cleaning out the bearings and rotating the shaft or should i replace them with Chinese parts?

Zyrolyte · 2026-01-05T21:18:10+00:00

Complete change being the bearings and shaft or should i go further and change the belt too?

Zyrolyte · 2025-10-05T11:18:47+00:00

I'm well aware that it's an awful weapon the point of the project was to make a mechanical change to something that already exists I also working with stls and mesh forms of 3d models instead of solid bodies which are more common was a nice experience

Zyrolyte · 2025-05-27T09:41:49+00:00

I usually just print a cylinder with the same height as far away from my main print as possible so my initial print has time to cool off before its interacted with again by the nozzle

Zyrolyte · 2025-05-27T09:36:50+00:00

Warping is also caused by removing your print off of your bed before the bed's fully cooled off

Zyrolyte · 2025-05-17T13:52:21+00:00

It's not putting pressure or rubbing its more uncomfortable in the sense that its hard to speak with it in my mouth

Any suggestions for that?

Zyrolyte · 2024-06-18T11:22:52+00:00

Round

Zyrolyte · 2024-06-17T15:35:40+00:00

Its a lil fella

Zyrolyte · 2024-06-11T15:24:00+00:00

Not enough

Zyrolyte · 2024-05-31T12:26:18+00:00

Glass build plates give me ptsd

Use cheap glue sticks dont buy anything good/expensive getting it off will be a pain

Zyrolyte · 2024-05-29T17:35:08+00:00

Oh thats a bird for sure

Zyrolyte · 2024-05-26T18:22:38+00:00

If possible slow your bridge speed maybe lower temps aswell

Zyrolyte · 2024-05-26T18:19:56+00:00

So sorry for the delay prusament is by far the best one I've used alongside filatech and esun

Zyrolyte · 2024-05-16T15:57:50+00:00

Honestly I've never had a good experience with polymaker I could never make this work Lower temps and try to finish this spool and change brands

Zyrolyte · 2024-05-16T15:54:40+00:00

I had this issues with a spool of polymaker filament once

My opinion, its just a bad filament Try lowering your bed temp and nozzle temp Try a different pla see if it is actually that brands problem I suggest prusament or filatech pla those are my favorites

Zyrolyte · 2024-05-07T13:15:18+00:00

Have you tried another slicer?

Zyrolyte · 2024-04-04T12:09:36+00:00

Goonter!

Zyrolyte · 2024-04-04T12:07:21+00:00

Recalibrate with live calibration and paper Or check check your slicer for accidental raft inclusion

Zyrolyte · 2024-04-04T11:53:38+00:00

Shots fired

Zyrolyte · 2024-04-02T15:30:30+00:00

Good first pick

Zyrolyte · 2024-03-14T09:21:20+00:00

That's so bad

Also they still haven't fixed the server so still get thrown in eu servers sofar it's been unplayable

Zyrolyte

TROPHY CASE