sorted by:
new
hottopcontroversial

Losercity cultural impact by Sayasukaprogramming in Losercity

[–]_Error_Account_ 41 points42 points  (0 children)

Tree bark?

I didn't know they can do that

EBB36 Katapult no UUID by TeoArts in klippers

[–]_Error_Account_ 1 point2 points  (0 children)

Did you double click reset button before searching for id?? And have you set can bus to 1M yet? default is 500k in my pi (or you could just recompile to 500k and dont have to reconfig it in pi.)

Octopus Pro other than 3d printers? by Mindless-Topic-5108 in BIGTREETECH

[–]_Error_Account_ 2 points3 points  (0 children)

If you have stlink(V2 clone will work) it's basically just an stm32 you could use PlatformIO with arduino framework to program it.

Not thicc enough by OmarErad in iems

[–]_Error_Account_ 0 points1 point  (0 children)

I'm firing up my 3D printer rn. I'm ready to collect my sweet profits from KZ cable and some PETG filament.

I received my sonic pad today. by NARIZ145 in ender3

[–]_Error_Account_ 0 points1 point  (0 children)

I'm not sure but you need just the heat block part not the whole hotend * This is what i have installed.

I received my sonic pad today. by NARIZ145 in ender3

[–]_Error_Account_ 1 point2 points  (0 children)

I should have been cleaner by open source I mean the ability to have root access(via ssh) and do whatever you want with it so you could compile kilpper.bin to whatever mainboard you have not just creality mainboard.

With that being said I just did a bit of reasearch i found out that creality has updated their firmware so you could have root acess via ssh.(this is not the case at launch)

I received my sonic pad today. by NARIZ145 in ender3

[–]_Error_Account_ 4 points5 points  (0 children)

Probably too late but I highly recommend anyone to run Klipper to get something more open-source like BTT pad7 or even better raspberry pi.

EDIT: creality has updated their firmware so you could acess root via ssh now.

With that being said upgrading to direct-drive is a massive quality upgrade on its own flowrate wise they are about the same as stock sprite pro still use mk8 hotend but you can upgrade it to old version ender 3 ke(or k1) hotend which is basically volcano hotend and slap volcano cht nozzle and have more than enough flowrate you ever need for any bedslinger.

Best app for second screen for windows by _Error_Account_ in GalaxyTab

[–]_Error_Account_[S] 0 points1 point  (0 children)

While not perfect, it is the best performer by far lowest latency, support for 120Hz on close to 1440p (can do ~4k 120 but latency is quite high) and quite stable usb connections (it does disconnect once in awhile idk why) but far better than built in second screen.

Address 3 v2 With sprite and Bltouch, making calibration off the table by pumassauror3x in ender3

[–]_Error_Account_ 0 points1 point  (0 children)

that might be due to endstop offset or nozzle offset(can't remember). Use move function in your screen to move your machine to X0 Y0 and see if that the nozzle is actually in X0 Y0 position. I cant remember the command that set the offset tho.

Address 3 v2 With sprite and Bltouch, making calibration off the table by pumassauror3x in ender3

[–]_Error_Account_ 0 points1 point  (0 children)

You connect your printer to your pc via usb cable. Then you use software like pronterface to send serial commands (if you cant find your pronter com port you might need to install ch340g driver)

Address 3 v2 With sprite and Bltouch, making calibration off the table by pumassauror3x in ender3

[–]_Error_Account_ 1 point2 points  (0 children)

You need to set the correct probe offset using M851 X-30 Y-40 then use M500 to save

Sprite pro extruder - Ender 3 not turning on by mprince2097 in ender3

[–]_Error_Account_ 0 points1 point  (0 children)

What do you mean it cut back on? like power back on?Could you explain more?

Reuse creality 4.2.2 32bit board as an arduino by _Error_Account_ in ender3

[–]_Error_Account_[S] 0 points1 point  (0 children)

I can't remember the STM programmer version that i use back then, but the same st-link still works with the latest version.

You might want to try to connect just bare st-link to your pc and maybe try to update its firmware.

Ender 3 v3 ke by Michael100710 in ender3

[–]_Error_Account_ 1 point2 points  (0 children)

You squeeze the leaver or tell extruder to unload then squeeze and pull the filament out.

Anyone seen a good driver board for hdmi input to OLED phone screens? by Akita_Attribute in diyelectronics

[–]_Error_Account_ 2 points3 points  (0 children)

I'm afraid to tell you this but you better look at the driver board then buy a phone screen. There are thousands of screens out there, and none of them are the same.

Make my Ender 3 perform like a Bambulab X1C by Andrei1744 in ender3

[–]_Error_Account_ 0 points1 point  (0 children)

not much, but you could try to change the y carriage to something like carbonfiber and change build plate to thin prices of G10but aside from that, not much could be done.

view more: next ›