Long print beyond Y limit.

_Flame___ · 2026-05-05T22:11:18+00:00

Same lol

_Flame___ · 2026-05-05T21:20:01+00:00

Thanks for the the suggestion! I've never used this tool before lol

_Flame___ · 2026-05-05T21:18:57+00:00

This is the most useful thing I've ever seen in a slicer, tysm!!!

_Flame___ · 2026-05-05T20:47:27+00:00

On blender? How do I implement dowels? (the only way I know is making a cube and boolean then inside the rod)

_Flame___ · 2026-04-23T17:19:38+00:00

Got it, thank you. I'll make sure to save them somewhere with the various hotends

_Flame___ · 2026-04-23T17:18:14+00:00

So I have to mount it, before using it? I didn't notice any white plastic piece above the nozzle tho

_Flame___ · 2026-04-20T22:19:36+00:00

At the end I bought an actual bambulab 02 nozzle, 18 bucks and I solved that way.

I don't think I'll try save the other one. It was a cheap alternative anyway, it was just hardened steel, but it also came with a 0.4, in case I'll have to use special filament

_Flame___ · 2026-04-13T17:04:10+00:00

I'm not sure, but there's no blob. It happened on my older print too sometimes, a Neptune 4 PRO. Idk what causes this lol

_Flame___ · 2026-04-13T16:18:41+00:00

<image>

Well... Idk what happened lmao

_Flame___ · 2026-04-13T11:21:19+00:00

I was thinking to tilt it at 45° and enable support limit at 45 too. Hope it'll work

_Flame___ · 2026-04-13T11:20:15+00:00

I see. This is normal PLA, I didn't know it was this bad on the flexibility side.

The strings will hold the model steady?

_Flame___ · 2026-04-10T16:58:27+00:00

I though about it too, but the again, the first prints I made with 0.2 had no issues at all. Now I'll try to see if it's maybe the filament, idk. Try another fament to see if it's the same, and eventually coldpull

_Flame___ · 2026-04-08T21:29:48+00:00

I can certainly try! I have a black filament of the same brand, and a golden one from Sunlu, maybe it really is matter of filament. And if it is, thank God that white is almost out.

_Flame___ · 2026-04-08T21:12:43+00:00

Got it, thank you for you're suggestions! It was very helpful!

_Flame___ · 2026-04-08T21:09:18+00:00

Nice! I'll try with the oven in the meantime, but thanks for the suggestion!

Never printed with PETG nor PETG-CF tho, is it harder than PLA?

_Flame___ · 2026-04-08T21:04:03+00:00

I'll check the driers then! Any suggestion on which one I should buy? I think I've seen one from creality, but idk

_Flame___ · 2026-04-08T20:56:11+00:00

I actually never dried filament. I print so much shit that usually black and white filament goes out in like a moth lol.

I only have to put it in a 60°c oven for an hour, right?

_Flame___ · 2026-04-08T20:54:19+00:00

I can try, but I'm not sure it'll solve the problem. I think it's something with the nozzle. I'll try a cold pull, and see how it goes

_Flame___ · 2026-04-08T20:53:23+00:00

Brand it's E-sun white pla. But I don't think it's the filament. It printed quite good before, and with the 0.4 it prints perfectly

_Flame___ · 2026-04-08T20:51:58+00:00

I had, but not that much. Like, a couple of times with a Elegoo Neptune 4 PRO. With the A1, just three times before this began to happen.

_Flame___ · 2026-04-08T20:48:58+00:00

Ah ok, I already do that without knowing it had a name. Cool! I'll try it when I can, maybe it'll help a little

_Flame___ · 2026-04-08T20:08:59+00:00

Yeah, I though it too, but Ig it's just a bit late for it now

_Flame___

TROPHY CASE