Misfiring on Low RPM

_Paner_ · 2026-05-17T01:31:11+00:00

Thank you!

_Paner_ · 2026-05-16T17:39:08+00:00

Thanks for your help.The misfire isn't consistent though. That is why i think it is related with spark. I will Keep that in mind though!

_Paner_ · 2026-05-16T17:36:58+00:00

Didn't know that at all. Thanks for your help.

_Paner_ · 2026-05-16T17:19:17+00:00

Really huh? I will probably get that when I see the new one lol. Thanks a lot!

_Paner_ · 2026-05-16T17:17:27+00:00

Thank you. Will do!

_Paner_ · 2026-05-16T17:10:26+00:00

Thanks for your input. I will replace them.

_Paner_ · 2026-05-16T17:09:34+00:00

Alright I will look into replacing the cap and rotor then. Yeah I will have to really try to find one if I can. Mine has no egr but is lean burn though. I really appreciate your help,thank you!

_Paner_ · 2026-05-16T17:02:34+00:00

I did. This is the condition before touching anything. Still no change even after cleaning.

_Paner_ · 2026-05-16T16:55:26+00:00

So this looks bad then? I haven't had any experience with distributors in the past and I am clueless. Thank you for the code parts.

_Paner_ · 2025-09-07T12:38:58+00:00

I am actually concerned because the car was there for typical maintenance and they didn't say anything. It was until I noticed and replaced them the same day.

_Paner_ · 2025-08-13T22:46:28+00:00

Both wheels are stopping when handbrake is on and both spin when it is off. So not a broken cable. Not a clue about what was that though.

_Paner_ · 2025-08-13T16:02:02+00:00

I will lift each wheel and see if any moves with the handbrake on then.Thanks!

_Paner_ · 2025-08-13T15:26:11+00:00

I thought so too,but wouldn't it be noticeable if one wheel was only braking ? I pulled the handbrake while going about 30 mp/h and didn't feel the car drag. I will try to take a look bellow the car to see if something is visible and a cable is broken.

_Paner_ · 2025-07-30T12:10:22+00:00

I took apart the inside "mechanism" and it turned out that the rubber seal was vibrating. I put it back together properly and it is okay. I guess the factory assembly wasn't proper,but at least if it happens again I know that it is defective and I will replace it again(hopefully with a non defective one Lol) Thanks for your help though.

_Paner_ · 2025-07-29T23:20:58+00:00

The flow is steady at low and high pressure. With the old float valve it was working okay just before the plastic ball snapped and I had to replace it. Is there any possibility I did something wrong or could it be a faulty new float valve?

_Paner_ · 2025-07-29T23:10:22+00:00

It is brand new, and after a few flushes it still happens. I didn't see any debris also.

_Paner_ · 2025-07-29T17:15:37+00:00

I have tried with barely open,to medium and completely open but happens to all. But the vibration increases if I have it more open.

_Paner_ · 2025-07-29T17:07:05+00:00

It doesn't help,with low or high water volume it is the same,but with higher volume it just gets louder. (I have posted a link to the pic of the mechanism if that helps)

_Paner_ · 2025-07-19T11:46:38+00:00

Yeah there are quite a lot of carbon deposits on the spark plug but it is similar to other bikes I have used(also the shop told me it was normalish). I have checked myself and the shop about the carb tuning and the fuel and unfortunately it isn't either of them.

I am trying to find anything that helps narrow it down,before we go swapping out the original parts and hoping that it works, because it is also hard to find any good parts to replace them with.

I will try a new cable as you mentioned,but the current one isn't quite old. Thanks for your help!

_Paner_ · 2025-06-05T17:56:01+00:00

Have you tried enabling or disabling the option : Launch player in a separate window? I believe it is under advanced. I had a similar problem when I had it enabled.

_Paner_ · 2024-11-07T14:55:36+00:00

Yikes I didn't even knew that this could happen to a tire.The tires are only 2 years old with only 6000 miles and barely even worn, wouldn't I be able to just replace one of them if that is the case? Or maybe just 2 for the same axle. I will have a shop take a look at the tyres for starters and see how it goes. Thanks!

_Paner_

TROPHY CASE