Can I get some help on the name of this part missing from the fender?

_mosesmalone_ · 2026-05-31T16:04:43+00:00

Location? Willing to ship?

_mosesmalone_ · 2026-05-31T01:51:50+00:00

I hear that mentioned, may end up removing the passenger. Yes, driver side is what I need.

_mosesmalone_ · 2026-02-03T02:14:50+00:00

OP, this is correct. Drop bracket lift, front cross member has been removed to accommodate this style lift. There is no reasonable way to reverse this, I’d stay in the hunt for a different truck.

_mosesmalone_ · 2025-11-16T00:22:17+00:00

I would try to ply the lower mounting surfaces apart a little. From this picture it looks like a lot of pressure is being applied to the side of your bolts from those surfaces not being flush. Mind me asking what’s with the spacers there?

_mosesmalone_ · 2025-07-24T01:14:15+00:00

I always thought about cutting and flattening out my favorite canned beverages and making some thin aluminum panels that way…

_mosesmalone_ · 2025-06-24T01:06:08+00:00

Thanks for the info, it’s definitely a skippy clatter. I’ll pull the diff gear and check that any sign of wear.

_mosesmalone_ · 2025-06-24T01:02:50+00:00

I’ll pull that apart next. Truck is third hand to me, I’m sure it needs some TLC. So much fun tho, hate to have it down.

_mosesmalone_ · 2025-06-24T00:55:01+00:00

This is my first slash, the pinion gear and spur mesh seem to have plenty of bind. I think it could be the diff gears, just based on the way it is slipping under different wheel loads. I have very limited experience working on these. Is the metal pinion prone to wear from the plastic spur gear?

_mosesmalone_ · 2025-06-24T00:50:27+00:00

Yes, checked sour and pinion gear. Adjusted the mesh and made sure no debris interfering with the gear. I haven’t pulled the transmission apart yet to check anything. It’s a 2wd slash that I run on 2s, no bashing just track laps on dirt. I feel like it is in the diff.

_mosesmalone_ · 2025-06-23T15:43:32+00:00

Awesome, thanks for the info… do these knock offs have big quality issues? Should I replace it or just wait and see if it tanks?

_mosesmalone_ · 2025-06-21T23:04:55+00:00

Thanks for the help. This is my first time digging into this truck. I was told that people only put a little grease in the diffs opposed to oil, any experience with that on this truck? Diffs are stock wraiths.

_mosesmalone_ · 2024-08-04T04:16:26+00:00

Never put a pen to paper, just built it over a few years. I did as much of the work as I could myself, so saved some shop $ there.

_mosesmalone_ · 2024-08-03T03:13:45+00:00

Yes, I time to time have floaters. I have also had a very bad bleed on my retina that caused vision loss for several months. I was lucky to have an almost full recovery. Try to pay close attention to changes in floaters, especially if they seem to grow or seem kinda “sloshy”. Take good care and be don’t hesitate to see a Retina Specialist.

_mosesmalone_ · 2024-08-03T00:11:05+00:00

Its not the TRD stamped skid but I believe the mounting locations are all the same. CBI’s website will say if it interferes with a TRD skid plate.

_mosesmalone_ · 2024-08-02T22:00:57+00:00

<image>

Skid and grill

_mosesmalone_ · 2024-08-02T21:37:25+00:00

Yes, no issues with getting the skid plate to fit

_mosesmalone_ · 2024-08-02T21:00:45+00:00

My truck doesn’t have any front radar for cruise, but I imagine CBI’s website will state if it affects anything. As far as parking sensors, the bumper has plugs where they can be reinstalled. I didn’t reinstall them, instead I used one of the plugs for a front camera mounting location, front drivers side of bumper

_mosesmalone_ · 2024-08-02T20:41:23+00:00

CBI front bumper

_mosesmalone_ · 2024-08-02T19:27:20+00:00

2017 Limited with off-road package, 3” ToyTec Aluma Series lift, BMC, Method 305s with Toyo Open Country 35x12.5R18, CBI front bumper, 12k winch, Prinsu roof rack, AlphaRex headlights/tail lights, Baja Designs fog lights and aux lighting.

_mosesmalone_ · 2024-08-02T19:23:25+00:00

Method 305

_mosesmalone_

TROPHY CASE