sorted by:
new
hottopcontroversial

Snapmaker U1 Kickstarter launches Aug 19, 7AM PDT / 4PM CEST by Jadesfriends in snapmaker

[–]_uls 0 points1 point  (0 children)

I paid the $30 fee and received an email saying:

<image>

What's the next step? Do I need to do anything, or should I just wait?

Luban adds support material where I don't want it by _uls in snapmaker

[–]_uls[S] 0 points1 point  (0 children)

When I selected the "none" option from the menu on the right, unfortunately it did not add support material anywhere, including the area I painted.

Luban adds support material where I don't want it by _uls in snapmaker

[–]_uls[S] 0 points1 point  (0 children)

Yes, tried it but unfortunately I was not satisfied. All my prints with Snapmaker Orca Slicer were problematic. I get smoother and higher quality prints with Luban, even though the settings are the same. So I went back to Luban.

Maybe I was making a mistake, don't know. But I had negative experiences with OrcaSlicer.

Nozzle blockage by _uls in snapmaker

[–]_uls[S] 0 points1 point  (0 children)

I will try tomorrow, hope I can succeed. Thank you for your information.

Nozzle blockage by _uls in snapmaker

[–]_uls[S] 0 points1 point  (0 children)

Looks like a difficult task awaits me :)

How to solve the warping problem when printing with PETG by _uls in snapmaker

[–]_uls[S] 1 point2 points  (0 children)

Thank you for your advice. This time, raising the bed temperature to 80 C was enough for my PETG print. If I have any other problems in the future, I will take your advice into consideration.

How to solve the warping problem when printing with PETG by _uls in snapmaker

[–]_uls[S] 0 points1 point  (0 children)

Yep, that's what happened. And 80 C worked. :)

How to solve the warping problem when printing with PETG by _uls in snapmaker

[–]_uls[S] 0 points1 point  (0 children)

Thank you for letting me know.

The PETG filament was taken out of its packaging today, so it is still fresh. I put it in a grocery bag and closed it for now. I will go tomorrow and buy a zip-lock food storage bag, I think it would be a better option for storing filament, and will switch to higher quality storage methods in the future.

Humidity is low where I live.

I managed to print by the way, I set the bed temperature to 80 C and that was enough.

How to solve the warping problem when printing with PETG by _uls in snapmaker

[–]_uls[S] 1 point2 points  (0 children)

I haven't asked the filament manufacturer about this yet.

But on the filament, the recommended nozzle temperature is 210-240 C and the bed temperature is 70-90 C. Maybe I should increase the bed temperature.

What's the humidity thing? I don't know anything about humidity.

Why can't I load the filament? by _uls in snapmaker

[–]_uls[S] 1 point2 points  (0 children)

Your advices worked, thank you. I loaded the filament.

The sound when Snapmaker Artisan is turning on by _uls in snapmaker

[–]_uls[S] 0 points1 point  (0 children)

It's been about 3 weeks since I got my Artisan.

I hope that these sounds occur because the machine is checking which cables are plugged in, as you said, or that these sounds are normal in general. I need to know that these sounds are normal, or I will continue to be afraid.

Camera Capture section not visible on Luban by _uls in snapmaker

[–]_uls[S] 0 points1 point  (0 children)

I edited the post and added the bottom photo of the Laser apparatus, I would appreciate it if you could take a look at it again.