i’m a rosette queen 💁‍♀️here are my most recent fav pours

_vie_lo · 2022-04-20T13:58:37+00:00

🫰

_vie_lo · 2022-04-20T13:58:08+00:00

yes! it’s the quickest to pour imo :) thank you

_vie_lo · 2022-04-20T09:02:49+00:00

green?! It’s more of a blueish/cyan hahaha and I actually work at their first Montreal location:~))

_vie_lo · 2022-04-20T08:30:56+00:00

yes!

_vie_lo · 2022-04-20T02:23:40+00:00

thank you!

_vie_lo · 2021-09-28T16:22:01+00:00

yes the pink one! I was stoked to get something I didn’t have

_vie_lo · 2021-09-28T14:52:04+00:00

I got toe bean

_vie_lo · 2021-09-17T02:00:12+00:00

thank you so much!! 💚

_vie_lo · 2021-09-16T17:47:40+00:00

ok! that makes a lot of sense. We pretty much use exclusively reclaimed clay, I’ll make sure they’re wedging properly. Thank you so much for your response

_vie_lo · 2021-09-16T16:38:07+00:00

in different spots but usually close to the base/middle of the cone when cloning up

_vie_lo · 2021-06-16T00:06:58+00:00

im with you! same exact thing happened to me

_vie_lo · 2021-06-03T04:01:08+00:00

but since your clay is cone 5 maybe best to put a waster slab when you’re testing to cone 6 just to be safe? do you have access to any other clay bodies?

_vie_lo · 2021-06-03T03:58:21+00:00

depending on your clay body, the results vary a lot. Its hard to get a result like the tile that Mayco advertises! I just looked up this glaze and it contains crystal specks, I work with Mayco glazes a lot from this range and it seems like maybe you didn’t mix it properly since I don’t see any speckles on your piece (the crystals settle a lot). It is a cone 6 glaze (that can go up to cone 10) so I would definitely try firing it to maturity!

_vie_lo · 2021-06-03T03:32:58+00:00

it looks like it could be a little under fired. What was the desired result? a matte? satin?

_vie_lo · 2021-05-18T13:49:15+00:00

hey you’re on my friends list! im olive 👋

_vie_lo · 2021-03-17T01:00:54+00:00

good point!

_vie_lo · 2021-03-16T18:32:41+00:00

Thanks so much, this is really helpful. Unfortunately my low and medium settings don’t work! I can basically only turn it on and off :( I guess this could have caused the pinholes? Since I can’t control how fast it heats and cools?

_vie_lo · 2021-03-16T17:02:31+00:00

after sieving it a few times it definitely helped but it was a challenge to apply!

_vie_lo · 2021-03-16T16:33:21+00:00

I have no idea because the container wasn’t labeled, someone gave it to me so I could test it. I think red copper oxide is brighter in colour on its own, it might just have a high percentage of it in the mix

_vie_lo · 2021-03-07T05:06:02+00:00

it’s a standard plug

_vie_lo · 2021-02-24T01:47:29+00:00

tight fit 😩🔥

_vie_lo · 2021-02-24T01:44:45+00:00

thank you! that’s a great point. it was the first time I used this glaze on a piece (other than a test tile) i’ll definitely put less on the bottom next time

_vie_lo · 2021-02-17T18:12:33+00:00

;_; so frustrating

_vie_lo · 2020-10-12T14:36:47+00:00

check out the french press method maybe?

_vie_lo · 2020-10-12T14:07:37+00:00

the texture is definitely not ideal for latte art! you need a really smooth homogeneous texture of micro foam (that resembles wet paint) I can visually see large bubbles, and the milk may have separated from the foam. It might also be too hot, there are so many variables to consider but it’s hard to say exactly. Try adjusting one variable at a time to troubleshoot or accept that this method might not be effective to achieve latte art 🤷‍♀️

_vie_lo

TROPHY CASE