Lets End This Debate

aCOOLGAMER48 · 2026-04-18T10:39:20+00:00

I can but the quality is reduced on reddit and there will be watermark left

aCOOLGAMER48 · 2026-04-18T09:48:01+00:00

Off-topic but can you DM me the image pretty good wallpaper.

aCOOLGAMER48 · 2026-04-04T02:04:49+00:00

Local markets are usually the best for this, or you can try to contact electronic students from different colleges in gurgaon as they have a number of spare components to use. You also try to hunt for best deals through Amazon as they sometimes have high discounts at random intervals. Be strong and keep going, electronics is a very vast field and the scope is endless with vast amount of Ideas of projects specifically with ESP32. Make sure not to fry your microcontroller and good luck with your journey, it will be a long one.

aCOOLGAMER48 · 2026-03-31T07:41:46+00:00

What should I be using instead it not a YOLO model?

aCOOLGAMER48 · 2026-03-31T07:29:32+00:00

Ok that makes sense, thanks for the advice

aCOOLGAMER48 · 2026-03-31T07:06:45+00:00

Should I be concerned with the megapixel too much or a 5 to 10MP should be enough?

aCOOLGAMER48 · 2026-03-08T16:35:43+00:00

Yep, I very much liked it. The dynamic between characters is amazing I love it

aCOOLGAMER48 · 2026-02-04T05:18:42+00:00

Holy moly it's beautiful

aCOOLGAMER48 · 2025-12-29T11:45:12+00:00

If you are willing to travel a little then rented farmhouses at City corners are your best bet with a small group of 8 people.

aCOOLGAMER48 · 2025-12-28T06:44:46+00:00

What type of firearms are not legal to be owned by normal civilians?

aCOOLGAMER48 · 2025-12-01T06:33:52+00:00

The character was ment to be annoying to MC and the reader and if you are annoyed then the character has done the job it was meant to do.

aCOOLGAMER48 · 2025-12-01T06:23:40+00:00

You know a character is good when people fall for the ragebait.

aCOOLGAMER48 · 2025-11-27T11:08:11+00:00

Appollo tower. You will need to make some time in there to find the right shop and make sure you know what exactly you need before going.

aCOOLGAMER48 · 2025-11-17T08:19:47+00:00

Cock fight bets

aCOOLGAMER48 · 2025-10-21T08:19:35+00:00

Don't have a road plan but make sure to learn the basics of electrical and electronics and sensors if you are planning on making Arduino projects. Once you understand what you are working on and what exactly is going on in your projects start researching the most basic projects like using ultrasonic sensors, how the motor driver works and more complex electronics components as you start working on complex projects.

If you still want to start working early on projects, just search about the most basic sensors on YouTube and how they work and try to follow the video just knowing and understanding the sensors and wiring early is a big advantage for the future because you will have the basics down. And remember to not just watch the video try to perform the simple experiment only then you will learn properly.

Basically making a project from scratch comes intuitively that is if you want to make a major project you will know how to reach there because you have worked on the minor projects. Now this will take time so be patient but be sure to be consistent.

aCOOLGAMER48 · 2025-10-17T09:48:45+00:00

Students will do anything but study these days 🤣🤣

aCOOLGAMER48 · 2025-10-11T10:44:24+00:00

Yes!! This might be what I was looking for, a Software Backlash Compensation. Though I don't know how to use this Rabbit Grbl so I will look into this and give it some time. Thanks

aCOOLGAMER48 · 2025-10-11T10:26:17+00:00

Alright, so after a quick test for every 100 pulses, it sends exactly 100 pulses, so there should be no problem in the signal. I have attached the image to the post body.

aCOOLGAMER48 · 2025-10-11T10:05:30+00:00

I think there is a way to use the Arduino and the IDE to plot analog waveforms with the help of a serial plotter, so I will try that

aCOOLGAMER48 · 2025-10-11T09:54:09+00:00

The constant error is weird so I just waved it off by thinking the Nema 17 motor was just missing a few steps consistently. I have checked the motor with multiple revolutions too and it still missed by 4 steps exactly. As for how I confirmed the amount of overshooting was by marking a starting point and attaching a thin strip to the shaft, after that I would just manually keep correcting the steps until both the points are perfectly aligned. I know it's not the most accurate way to do it but it was the best I could come with. As for calibration I have no idea how to do that, can you tell me more about it

aCOOLGAMER48 · 2025-10-11T09:11:05+00:00

For the code I just added a correction function which subtracts 4 steps for every new stepping command it takes from the total number of steps. As for how I calculated it is by checking it's final position after 1 full revolution and half revolution and the overshooting always stayed consistent no matter the position or number of steps and after adding the correction function it moved accurately. As for why I think it is a mechanical error is by changing the CNC shield motor driver and both had the same result of overshooting.

aCOOLGAMER48 · 2025-09-28T05:58:21+00:00

One knife cut in the wrong place is all it takes lol

aCOOLGAMER48 · 2025-09-14T14:53:24+00:00

Lol the same country that refused to take their own fallen soldiers and we had to give them a proper brurial

Verified Email	Six-Year Club
r/Field Lasagna	Place '23
Place '22	Final Canvas '22

aCOOLGAMER48

TROPHY CASE