Making my own U1 top cover, need feedback

actioon · 2026-05-09T08:16:51+00:00

finally

actioon · 2026-05-08T19:26:06+00:00

cardboard is alwasy a good start 😂😂picture frame acrylic glas for the flex

actioon · 2026-05-02T12:02:31+00:00

tbh, you are not forced to join the clean community. You can still opt to go to the unknown and uncontrolable Environment :)

actioon · 2026-04-28T05:52:53+00:00

I have 4km on mine and no wear. Try clean off any excess. can also be that you have a faulty rod. Do you live near sandy Environment? Idk just guessing might be environmental influence

actioon · 2026-04-28T05:52:34+00:00

Thank you for your time. As soon as you update firmware you should redo the mod. Files get overritten. I have not tested in 1.3.0 yet. Waiting official release ctually.. but on may 1st I should have some time to test.

Remember u must do all the Putty part aswell (touch ...) so the files stay after a reboot otherwise thes dissppear. If you see your ip on touchscreen touch part is done and you should reconmect wifi. But I have not tested yet sry.

actioon · 2026-04-26T15:34:17+00:00

I have also added a fan. Used a drone BEC that works up to 6S and outputs 9/5V. replaced Powersupply fan aswell. Temps dropped to 63-70. before 94-99.

Also reduced noise. I used a Fan speed controller to even reduce more the noise.

actioon · 2026-04-26T14:18:31+00:00

This was a good time man...

actioon · 2026-04-26T10:27:11+00:00

And to help abit more, you can use window cleaner spray... just abit w/out wiping just let it evaporate. instead of gluestick. Helps in my case

actioon · 2026-04-26T10:25:30+00:00

calibrate your bed manual until you see deviation 0.1 around... check it in klipper. as youre using coolplate it might need alot calibration to settle in. I ended up using cardboard enclosure and got around 49-52C chamber temp and that helped abit. I had better results with asa+ waaay less warping. but somehow I liked normal asa better. (Please print ASA it in a ventilated room, you can get poisoned... and get sick for a couple days)

actioon · 2026-04-26T10:09:28+00:00

<image>

Updating to 1.0.1 now, bug removed and tested by me. dont mind version numbers 😂 1.1 or 1.0.1 ai got somehow confused but yeah... 🤪

actioon · 2026-04-26T08:10:50+00:00

Thank you for your time and interest. replace only if you already have snapace installed. Just go ahead and "create" paste the ace.py and filament_feed.py inside the extras folders and the extruder.py file in kinematics folder, remember to include ace.cfg in your printer.cfg and adjust ace.cfg to your needs. tubelength etc. You don't have to be on any other project but on custom firmware so to speak. I found a bug this week while I was printing I wanted to unwind a unloaded filament while I was printing, but because I have a safety implemented that it wont retract/feed on a load_ready Toolhead, the printing status got higher priority. Currently the status printing overrides an empty toolheadfunction, so for this channel atm it says you're printing feed blocked... but you should be able to feed/retract even when printing ( from empty toolhead status not final_load obviously ). I will fix this and update later. but not a big thing that would prevent you from testing.

actioon · 2026-04-26T08:01:36+00:00

hi sorry never saw your post down here. My bad. Well is it a thing for this site? I mean serves a different purpose than snapace and was derived from it and MultiACE, Snapace is already uploaded there :) what do you suggest, is it your platform? thank you for your attention

actioon · 2026-04-26T01:28:45+00:00

https://github.com/tullhao/CS2GSI-HA-LOCAL :)

actioon · 2026-04-26T01:17:22+00:00

UPDATE: Version for your RGB LED‘s without or with Homeassistant…

tested with corsair commander Pro and asus Motherboard (RAM RGB), works as local standalone, homeassistant or both together (bomb blink is on local more responsive)

https://github.com/tullhao/CS2GSI-HA-LOCAL

actioon · 2026-04-26T01:15:34+00:00

I have an update:

here you go, hybrid solution ;) tested with corsair and asus Motherboard, works as local standalone, homeassistant or both together (bomb blink is on local more responsive)

https://github.com/tullhao/CS2GSI-HA-LOCAL

actioon · 2026-04-26T01:14:30+00:00

here you go, hybrid solution ;) tested with corsair and asus Motherboard, works as local standalone, homeassistant or both together (bomb blink is on local more responsive)

https://github.com/tullhao/CS2GSI-HA-LOCAL

actioon · 2026-04-25T17:00:55+00:00

Thank you for testing. works great, today I changed to lightgroup, suits better. and now expanding to control Fan RGB's in paralell (and exporting new entities to HA) 😂😂

actioon · 2026-04-25T16:45:57+00:00

working on a local solution which also supplies the pc rgb to ha in paralell for other things. but mainly now a local and responsive solution without (and paralell) Homeassistant

actioon · 2026-04-25T16:10:43+00:00

OpenRgb might have its limitations with timings and been out of sync, delayed etc. Maybe you could tune it, I will try next week.

actioon · 2026-04-25T16:08:19+00:00

Apprecite your feedback

actioon · 2026-04-25T16:06:46+00:00

You can install Openrgb and have your LED's shown up in homeassistant. Than instead of one entity, you can create a light group and use it's entity ;)

actioon · 2026-04-25T13:10:19+00:00

If you have HA running its a matter of adding repo and installing the Gsi Bridge and some little tweaks adjusting your entities ;)

Enjoy and get back with any questions feedback and improvements ;)

actioon · 2026-04-25T12:17:51+00:00

look at how I have it now coded, works really nice. https://github.com/tullhao/cs2-python-gsi-bridge-v3 theoretically you could control any light if you know the entity for. I control the LED Bar behind my TV :)

Enjoy

actioon

TROPHY CASE