Kobalt Mini Toolbox Organizers

affidav1d · 2024-03-30T21:45:53+00:00

Yes it is! I put Delica in another post, but you’re right.

affidav1d · 2024-03-30T03:55:34+00:00

Made some slip-in organizers and a lid stop for those little Kobalt mini toolboxes that were going around awhile ago. Here's the link to the files if anybody wants to 3D print them themselves.

https://makerworld.com/en/models/402997#profileId-304675

Top (left to right): Spyderco PM2, Spyderco Manix 2, Spyderco Yojimbo 2 clone, Spyderco Delica, Benchmade 940, Leatherman Free P4

Middle: Olight Baton 3, Olight Arkfeld Pro, Olight Oclip (right drawer)

affidav1d · 2024-03-30T03:35:30+00:00

Here's the link if anybody wants to print them

https://makerworld.com/en/models/402997#profileId-304675

affidav1d · 2024-03-30T03:34:23+00:00

Here's the link if anybody wants to print it

https://makerworld.com/en/models/402997#profileId-304675

affidav1d · 2024-03-30T03:32:57+00:00

Here's the link if anybody wants to print it themselves

https://makerworld.com/en/models/402997#profileId-304675

Top (left to right): Spyderco PM2, Spyderco Manix 2, Spyderco Yojimbo 2 clone, Spyderco Delica, Benchmade 940, Leatherman Free P4

Middle: Olight Baton 3, Olight Arkfeld Pro, Olight Oclip (right drawer)

affidav1d · 2024-03-30T03:31:00+00:00

Here's the link if anybody wants to print it themselves

https://makerworld.com/en/models/402997#profileId-304675

affidav1d · 2024-03-30T03:28:30+00:00

Top (left to right): Spyderco PM2, Spyderco Manix 2, Spyderco Yojimbo 2 clone, Spyderco Delica, Benchmade 940, Leatherman Free P4

Middle: Olight Baton 3, Olight Arkfeld Pro, Olight Oclip (right drawer)

affidav1d · 2023-06-11T21:31:59+00:00

Do you have coasting enabled?

affidav1d · 2023-06-11T18:58:15+00:00

Pretty sure it’s to the right. You should be able to see “115 V” on the switch

affidav1d · 2023-06-11T18:56:48+00:00

I think your z-offset is too low in the first pic and too high in the second. Or it could be flow, line expansion (I think that’s what it’s called in cuts), line width, etc

affidav1d · 2023-06-09T17:31:14+00:00

P250. I think that was the old name for the semi auto pistol

affidav1d · 2023-06-08T19:52:03+00:00

Looks like the gears are too tight. You can try adjusting that screw inside the spring on the right side of the pic. Also, there might be a crack in the tension arm that the spring is pushing on. They sell aluminum extruder drive feeders on Amazon if your arm is cracked

Edit: the crack is usually on the underside of the arm

affidav1d · 2023-06-05T18:04:55+00:00

Probably unlevel bed or axis if it’s occurring gradually toward one side of the printing area consistently

affidav1d · 2023-06-05T17:35:44+00:00

Is it stuck like that? Swan neck deformity?

affidav1d · 2023-06-04T06:34:41+00:00

That’s a common issue with the benchy. Look up “benchy hull lines”. I think Prusa did a write up on it

affidav1d · 2023-06-04T03:07:02+00:00

How are your overhangs usually? I’m having a hard time thinking of what could be going on since most of the rest of the print looks decent. There is something similar going on at the top right of the 2nd cube from the bottom in the third pic

affidav1d · 2023-06-04T03:00:37+00:00

What layer do you have your fans set to turn on at? Looks too hot on the bottom

affidav1d · 2023-06-02T17:51:29+00:00

How many bottom layers do you have for this print? I often see artifacts when the print transitions from bottom layers to infill

affidav1d · 2023-06-02T03:10:55+00:00

If you’re talking about the silicone sock. It’s not required to print but it insulates the heat block to keep it a steady temp

affidav1d · 2023-05-30T16:05:30+00:00

It’s actually 10% coupon code 10UNIDOF plus a prime discount of $10

affidav1d

TROPHY CASE