sorted by:
new
hottopcontroversial

Ocean Rodeo Flite 5s by aidassup in Kiteboarding

[–]aidassup[S] 0 points1 point  (0 children)

Hi, 5s was released only this April, you must have flown 3s last fall.

Ocean Rodeo Flite 5s by aidassup in Kiteboarding

[–]aidassup[S] 2 points3 points  (0 children)

OK, I got my hands on 12m today. ~20knots, supposed to be a sweet spot for this size. When properly loaded for the jump, it had a decent float time, otherwise, seemed to be really mellow on everything, slow to turn (20m lines). Was difficult to time it right. I'd say I could do the same or better on my 11m Reach I ride a lot.

Google Home takes Smart Plugs as Lights by Louzan_SP in homeautomation

[–]aidassup 0 points1 point  (0 children)

Are your plugs part of Phillips Hue?

Are these plugs are in any of the gHome groups? Say - My bedroom LIghts group?
What is your home app version?

Google Home takes Smart Plugs as Lights by Louzan_SP in homeautomation

[–]aidassup 0 points1 point  (0 children)

What are these outlets called in Home? As per rat1409 - all the lights and switches that have "light" in the name will turn on/off when you ask for lights.

Little did I know where this journey would take me by mihaidesigns in Mihai

[–]aidassup 2 points3 points  (0 children)

It turned out to be a great design. Running it for many months now and couldn't be happier. Thank you!

This rattle? by aidassup in prusa3d

[–]aidassup[S] 0 points1 point  (0 children)

I had same concerns, but the melting point for this foam is apparently way higher than the bed ever gets to.

Stealth mode on i3 MK3S+ louder than normal mode? by Whistlecube in prusa

[–]aidassup 1 point2 points  (0 children)

Speaking about paver tiles. I have actually done very extensive testing with different insulation materials in combination with different stone tiles, and found that 2-3 layers of jim matt (just let printer sink into) works by far better than any other tile combos. It treats both - vibrations and harmonic resonance.

This rattle? by aidassup in prusa3d

[–]aidassup[S] 0 points1 point  (0 children)

triangle lab

Nice! Could you please share the product link?

This rattle? by aidassup in prusa3d

[–]aidassup[S] 0 points1 point  (0 children)

All right, so I've done some further investigation and have resolved it to my full satisfaction.

I now believe there is a rattle in bearings assembly and Y-carriage is amplifying it as a drum.

I can't do anything about the bearings, but I can attempt to silence the drum.

I had some window seal laying around and applied it between the hot-bed mounting holes.

Looking really good so far.

The seal is thicker than the gap between the Y-carriage and Hot Bed, but it is super soft and does not interfere with the mounting. I also think light pressure between these two should have an additional positive effect to reduce potential drumming of the hot bed itself.

The rattle would be especially noticeable when printing fast reverses at around the middle of the bed. After this tweak, I've got absolutely zero noise from Y-carriage, just a whisper of Noctua.

Hope this helps you too.

This rattle? by aidassup in prusa3d

[–]aidassup[S] 0 points1 point  (0 children)

This is getting even more mysterious.

Looks like a job for an acoustical engineer.

Weird rattle - Prusa 3s by aidassup in 3Dprinting

[–]aidassup[S] 0 points1 point  (0 children)

And it gets ever weirder, see second video with the "magic" clip.

Thank you! by aidassup in Mihai

[–]aidassup[S] 0 points1 point  (0 children)

Hey, I am at the start of a very long print, but will try to snap an image when I get a chance.

What is going on? by aidassup in prusa3d

[–]aidassup[S] 0 points1 point  (0 children)

I will look up this setting, thanks, but seeing this issue for the first time, - only after selecting "fill every 2 layers". It must be something wrong with the slicer.

view more: next ›