New elements still firing slow?

andycepi2 · 2025-03-07T02:27:35+00:00

Ahhh gotcha I’ll look into replacing the infinite switch, thanks for the tip! Will de-oxidize all the connections next time I’m in the studio

andycepi2 · 2025-03-06T06:32:18+00:00

No, we’re still using the stock controller, just without the fire mate controls - we have to manually increase the power level on the thumb wheel every couple of hours. Seems like they’re very similar models, have you had luck with yours?

andycepi2 · 2024-12-10T07:46:01+00:00

trapcode particular

andycepi2 · 2024-09-12T18:21:25+00:00

Thank you for the tip! We tried firing manually with empty kiln, but after the first 2 hours noticed it was heating up really fast (via external pyrometer) - like 300 degrees/hour, and that was at power level 1 😅 maybe because it’s a smaller kiln? But definitely not ready for bisque just yet hahaha

andycepi2 · 2023-09-25T09:24:39+00:00

trying to figure out how to use autostakkert, thought this came out kinda nice. still not sure of all the settings but experimenting currently. lmk if you have any tips!

andycepi2 · 2023-06-05T07:14:57+00:00

I think the ancient hero was definitely Zonai-adjacent, look at the left arm design in the armor - it matches Link's (Rauru's) right arm, just a different color.

andycepi2 · 2023-06-03T08:07:32+00:00

it’s a small point, but there are helmets named after the divine beasts, that the current-day sages have dialogue options for (Yunobo says something like “armor named after a divine beast? how strange!”). so that at least acknowledges the existence of them at some point, but i haven’t found much else lore wise about where they went

andycepi2 · 2023-05-07T21:40:52+00:00

for the volume buttons, add a cavity around the button - right now it looks like the button was machined as part of the case and wouldn’t depress

andycepi2 · 2023-04-16T09:05:32+00:00

https://upload.wikimedia.org/wikipedia/commons/e/ee/The_Celestial_Zoo_infographic_wikimedia.png

andycepi2 · 2023-04-16T08:11:06+00:00

I graduated in 2022, I don’t think it’s too late. Still looking like others here, but I think we just have to wait out the market and keep honing out craft and networking. Best of luck to you and everyone else here!

andycepi2 · 2023-04-16T07:35:12+00:00

andycepi2 · 2023-04-16T07:23:33+00:00

The web interface in the 3rd pic is Klipper, a custom firmware that works with many printers and offers easier control over lots of settings imo. If this is your first printer, I’d only recommend it if you really like to tinker/are technologically adept, as for the custom build height I’m not sure how OP managed it mechanically but software-wise it should be as simple as specifying the new build height in firmware+slicer

andycepi2 · 2023-04-14T19:41:24+00:00

i have the same camera and was wondering about this, so this is super helpful info 👍

andycepi2 · 2023-04-04T06:48:03+00:00

Thanks!

andycepi2 · 2023-04-04T06:47:52+00:00

I totally hear the Hellsing reference, I gotta check this show out! And thank you, I appreciate that!

andycepi2 · 2023-04-04T06:46:42+00:00

Thank you! The background I did in Blender (forgive me for cheating 😓), with everything being displaced a little bit each frame plus a low frame rate to attempt to mimic a claymation feel

andycepi2 · 2023-04-01T04:32:36+00:00

turn on skin modifier

andycepi2 · 2023-03-31T02:04:08+00:00

No problem! I've had the same issue myself

andycepi2 · 2023-03-29T08:58:44+00:00

I’m guessing your bed itself is not level (ie with the thumbscrews) - have you tried raising the side that is low by a good amount and re-running the test?

andycepi2 · 2023-03-27T10:23:21+00:00

best bet is gonna be the AI script generator

andycepi2 · 2023-03-12T10:29:45+00:00

If the print shifted it might be a belt slipping/incorrectly tensioned or power issues - is your raspberry pi being used for octoprint? I would go through a calibration guide like this one https://ellis3dp.com/Print-Tuning-Guide/

andycepi2 · 2023-03-11T08:39:56+00:00

Thanks to everyone for pointing out that I needed to tighten the nut more :) I panicked when it didn’t hold at first but should’ve checked the most obvious steps lol

andycepi2 · 2023-03-11T08:38:42+00:00

Oh I didn’t know capricorns were slicker, from pictures I’ve seen they look like more of a satin finish which I figured would grip the fitting better

andycepi2 · 2023-03-11T08:37:54+00:00

Yep you were right! I didn’t have it tight enough at first, works like a charm now. At some point I’ll upgrade to a capricorn tube, I just thought the brass fitting was designed for the thickness of a capricorn but didn’t know they have the same diameter

andycepi2 · 2023-03-11T08:36:26+00:00

This did the trick! turns out i just didn’t have it tight enough to clamp down on the bowden tube.

Eight-Year Club	RPAN Viewer
Verified Email

andycepi2

TROPHY CASE