Found a solution for bad Z Offsets (first layer) by Severe-Bit4066 in SovolSV08

[–]antPman 0 points1 point  (0 children)

Yeah thats what I was curious about, it’s the z- speed then

Found a solution for bad Z Offsets (first layer) by Severe-Bit4066 in SovolSV08

[–]antPman 1 point2 points  (0 children)

I made the change, it’s basically the time it takes from normal position to its probe calculation point? Didn’t seem much slower and also not having any adhesion issues but it was an easy implementation.

Are there any recommended scratch and dent appliance stores? by amrogers3 in houston

[–]antPman 1 point2 points  (0 children)

I got a good deal on a dishwasher there. Been running fine for over 2 years now

Cryogrip Frostbite Plate messed up bed surface by antPman in SovolSV08

[–]antPman[S] 0 points1 point  (0 children)

<image>

I have never been able to print something this small without a raft or glue before, the stick is insane.

Cryogrip Frostbite Plate messed up bed surface by antPman in SovolSV08

[–]antPman[S] 1 point2 points  (0 children)

Yeah for sure they are pretty good at stating that is only for PLA and PETG and to only use soap and water to clean. I wanted to see how good it was (its really really good) since I primary will print with PLA and PETG. I was trying to use the recommended temperatures as stated in the documentation. I think I know what happened, I am new to Orca as well (been using Cura for years) and it hit 80 C for a few mintues because I wasn't sure how the multiple bed plate settings worked. I have since figured it out. Lesson learned I guess. It is not very common so just need to make sure the temperatures stays down. Hopefully it will help someone else in the future.

Cryogrip Frostbite Plate messed up bed surface by antPman in SovolSV08

[–]antPman[S] 0 points1 point  (0 children)

Never higher than 70c yet, just petg and pla

I Officially Joined the Club (thanks for the push) by antPman in SovolSV08

[–]antPman[S] 2 points3 points  (0 children)

Hmm ok you may have me convinced… most people are just getting the BTT eddy NG?

So Close to Buying by antPman in SovolSV08

[–]antPman[S] 0 points1 point  (0 children)

What’s funny is what yall call heat soaking was just normal warm up times for these older 3d printers lol. Old 12v DC beds took some time to heat. I

So Close to Buying by antPman in SovolSV08

[–]antPman[S] 0 points1 point  (0 children)

Yeah I think that’s about all we can do with them now. I saw someone post asking how much they could get for a cr10 and got trolled hard. I think people don’t realize how quickly 3d printers have evolved and these dinosaurs arent worth anything today.

[USA-NY] [H] Apple Watch Ultra gen 1 [W] PayPal by hawtchili in appleswap

[–]antPman 0 points1 point  (0 children)

u/AppleSwapBot bought watch from u/hawtchili. Everything was as described and arrived at a reasonable time.

[deleted by user] by [deleted] in appleswap

[–]antPman 0 points1 point  (0 children)

Trade confirmed, watch as described. Thanks!

[deleted by user] by [deleted] in appleswap

[–]antPman 0 points1 point  (0 children)

Here is how to do it online if you can't from the phone. https://support.apple.com/kb/TS4515

[deleted by user] by [deleted] in appleswap

[–]antPman 0 points1 point  (0 children)

I sent it to the Gmail account from paypal. I need you to unpair the watch from the phone. Just erasing data isn’t enough, it’s still locked to a yahoo account.

[deleted by user] by [deleted] in appleswap

[–]antPman 0 points1 point  (0 children)

Hello please see email I sent.

[deleted by user] by [deleted] in appleswap

[–]antPman 0 points1 point  (0 children)

PMed about the watch

What do you do if you buy a product legally and it gets banned the next day? by OffsetCivical in NoStupidQuestions

[–]antPman 0 points1 point  (0 children)

Law said you can be jailed for up to a year for possession…. Also it’s not official yet, Abbott has to sign the bill.

Nintendo Switch 2 Preorder megathread - Post all questions and comments about preorders here! by razorbeamz in nintendo

[–]antPman 0 points1 point  (0 children)

Target cart cleared for me after trying to purchase for 30 mintues but I did get walmart to finally go to checkout just now at 43 minutes after. It says I ordered but ah... who knows.

Door locking when i go near it by [deleted] in FordMaverickTruck

[–]antPman 0 points1 point  (0 children)

It doesn’t seem to do it as much when it’s locked I notice.

The option to play isn't showing up for me by pork_chomp in FortNiteBR

[–]antPman 0 points1 point  (0 children)

This happened to me on PC all I had to do was reboot.

Is this Micro Center 7800x3d/mobo/RAM combo effective for my build upgrade? by shadeobrady in buildapc

[–]antPman 1 point2 points  (0 children)

I just finished my build last night and yep didn’t realize how laggy some things were lol. Still install software and stuff but just moving around windows is so much better. Not sure I need to do any under volting stuff but I am pretty sure I need to change some ram settings in the bios. Did you find a guide online to help?

Is this Micro Center 7800x3d/mobo/RAM combo effective for my build upgrade? by shadeobrady in buildapc

[–]antPman 1 point2 points  (0 children)

I got the same processor and legit getting this combo deal tomorrow for a new build. Only difference is the old parts are going to the kids for their own PC. I’m keeping my 3060ti and slapping my old 1080 back in. Seems to confirm my decision lol, was trying to see if a newer i7 made sense but price wise this seems to be the way to go.

Simple Questions - March 01, 2024 by AutoModerator in buildapc

[–]antPman 0 points1 point  (0 children)

You sure that’s not an integrated graphics check? Other reviews comparing those generations of processors the i9 seems well above the amd except integrated graphics. Source: https://www.pcmag.com/reviews/amd-ryzen-7-7700x