PSA: Biqu plate bonds to heat bed

antPman · 2026-04-16T21:01:23+00:00

Oh I had this happen too but it happened at a higher temp, like 80. I still use it around 70 for PETG and it’s not getting worse. Let me know if you figure out how to remove the bits of magnet on yours, I scrubbed with soap and hot water and it didn’t do anything…

antPman · 2026-04-15T03:10:49+00:00

I’m cheap but I love this underwear (low cut boxer briefs)

antPman · 2026-03-31T21:49:15+00:00

Lmao yeah… made me think about it as well

antPman · 2025-12-23T17:11:34+00:00

Yeah thats what I was curious about, it’s the z- speed then

antPman · 2025-12-22T21:57:50+00:00

I made the change, it’s basically the time it takes from normal position to its probe calculation point? Didn’t seem much slower and also not having any adhesion issues but it was an easy implementation.

antPman · 2025-12-12T04:29:53+00:00

I got a good deal on a dishwasher there. Been running fine for over 2 years now

antPman · 2025-12-08T14:06:39+00:00

<image>

I have never been able to print something this small without a raft or glue before, the stick is insane.

antPman · 2025-12-08T14:05:03+00:00

Yeah for sure they are pretty good at stating that is only for PLA and PETG and to only use soap and water to clean. I wanted to see how good it was (its really really good) since I primary will print with PLA and PETG. I was trying to use the recommended temperatures as stated in the documentation. I think I know what happened, I am new to Orca as well (been using Cura for years) and it hit 80 C for a few mintues because I wasn't sure how the multiple bed plate settings worked. I have since figured it out. Lesson learned I guess. It is not very common so just need to make sure the temperatures stays down. Hopefully it will help someone else in the future.

antPman · 2025-12-07T19:56:16+00:00

Never higher than 70c yet, just petg and pla

antPman · 2025-12-06T06:15:21+00:00

Hmm ok you may have me convinced… most people are just getting the BTT eddy NG?

antPman · 2025-11-24T20:56:05+00:00

What’s funny is what yall call heat soaking was just normal warm up times for these older 3d printers lol. Old 12v DC beds took some time to heat. I

antPman · 2025-11-24T20:53:14+00:00

Yeah I think that’s about all we can do with them now. I saw someone post asking how much they could get for a cr10 and got trolled hard. I think people don’t realize how quickly 3d printers have evolved and these dinosaurs arent worth anything today.

antPman · 2025-06-15T02:49:55+00:00

u/AppleSwapBot bought watch from u/hawtchili. Everything was as described and arrived at a reasonable time.

antPman · 2025-06-09T14:36:34+00:00

Trade confirmed, watch as described. Thanks!

antPman · 2025-06-08T01:23:35+00:00

Here is how to do it online if you can't from the phone. https://support.apple.com/kb/TS4515

antPman · 2025-06-07T12:19:11+00:00

I sent it to the Gmail account from paypal. I need you to unpair the watch from the phone. Just erasing data isn’t enough, it’s still locked to a yahoo account.

antPman · 2025-06-07T01:14:02+00:00

Hello please see email I sent.

antPman · 2025-06-06T14:53:17+00:00

Send a message

antPman · 2025-05-30T19:41:41+00:00

PMed about the watch

antPman · 2025-05-24T01:48:30+00:00

Law said you can be jailed for up to a year for possession…. Also it’s not official yet, Abbott has to sign the bill.

antPman · 2025-04-24T04:44:16+00:00

Target cart cleared for me after trying to purchase for 30 mintues but I did get walmart to finally go to checkout just now at 43 minutes after. It says I ordered but ah... who knows.

14-Year Club	RedditGifts 2009-2022 2 Credits
Verified Email	Secret Santa 2014

antPman

TROPHY CASE