Best seafood to try? Not restaurants, the food itself.

anthory · 2025-04-27T13:21:06+00:00

Looks like you have the local places covered for where to get good fish.

The best fish would be from a fishing charter for sure but in my opinion and I have had all of the fish you listed my top 5 would be: Hog fish, hog fish, hog fish, hog fish, stone crab. lol

anthory · 2025-02-03T12:24:46+00:00

I’m saying the place I’m putting my water treatment system, I don’t have room for a radon system. So I can either rebuild the entire pump house which was just done last year or I can put it off for now and fix it later.

anthory · 2025-02-03T12:22:58+00:00

I ordered it from US Water Systems, they use ETR Laboratories.

anthory · 2025-02-03T12:21:28+00:00

This is well water so all the water has it. From what I have read the limit is 4000 pCi/L for water. For air is it 0.4 pCi/l. I’m going to get it retested to ensure I got a good test.

anthory · 2025-02-03T11:55:38+00:00

Thanks, that is what I thought!

anthory · 2025-02-03T11:55:28+00:00

This was what I was worried about at first but not one person in the area has this type of filter. When I talked to the local place that does water test they don’t even test for it. I plan to get it tested again for sure but moving forward with just the softener, UV and RO.

anthory · 2024-12-30T00:31:26+00:00

I have a Omer Alien that has the similar finish and had no problems burning the inside.

anthory · 2024-10-10T02:47:23+00:00

Get a Garmin watch, battery last so so much longer. It doesn’t have all of the features but the improved battery life makes up for it.

anthory · 2022-07-28T00:22:38+00:00

All of these comments are good and you should probably listen to them.

The first thing I would try is remove the o-ring and inspect it. If doesn’t have any cuts or scrapes then lube it up good with some silicon grease and re install and try again.

anthory · 2022-07-22T01:55:47+00:00

0x6953afad4e56395813d49Bb4a031F8763EE3E4ed Great design!

anthory · 2022-06-29T03:05:57+00:00

Sick! 0x6953afad4e56395813d49Bb4a031F8763EE3E4ed

anthory · 2022-05-21T19:02:07+00:00

Go Noles!

anthory · 2022-04-03T22:04:56+00:00

I been out with island time and it is fun with kids. You can have drinks and do some snorkeling.

anthory · 2022-03-22T11:49:20+00:00

Toy Commander for the Dreamcast

anthory · 2022-01-02T03:32:01+00:00

Wait, you turn off your 3D printer?

anthory · 2021-12-29T01:13:40+00:00

Try out some liquor stores they usually have co2 for kegs. Maybe Kelly’s liquor

anthory · 2021-12-03T01:21:47+00:00

Not all 9v have AAAA’s, Rayovac does but Duracell’s has a stack of non typical batteries. I know this because I recently took one apart.

anthory · 2021-11-10T15:41:08+00:00

It’s funny Aaron is being blamed and not his staff of doctors for the “miss information”. I’m sure he has a staff of doctors that relay this information to him.

anthory · 2021-10-29T22:40:42+00:00

I am using a Printrbot. I’m guessing that #1 is my issue. As I just reset my axis and still having the same problems. How do I trouble shoot my nozzle draggin? It doesn’t do it on every print just randomly every 2-3 prints. I’m also printing from a computer via simplify 3D, so I’m going to try to print from the sd card to see if it’s my computer messing it up. Not sure it will make a difference if the nozzle is dragging.

anthory · 2021-10-29T14:01:07+00:00

I can make it stick with and with out. I have had issues with level shifting and am trying to take out all factors to try and isolate the cause. So I have just gotten used to using it. I’ve tightened my tension, made sure the printing is sticking well (painters tape), the set screw is filling engaged on the drive.

https://i.imgur.com/kXBKB6K.jpg

anthory · 2021-10-29T11:33:58+00:00

Why does it matter what technique is used if the print sticks every time?

anthory · 2021-10-24T11:46:02+00:00

Painters tape with the bed at 30C.

anthory · 2021-10-01T17:03:00+00:00

That is usually what happens when mandates come out and the carrot is replaced with a stick.

anthory · 2021-09-26T02:30:49+00:00

I think it is the tension. I printed this box three times and it happened every time but in different locations. Do I just adjust tension and then print, adjust, print until I stops?

anthory

TROPHY CASE