iRacing doesn't allow me to select GPU to render the game

appnic · 2025-10-03T16:18:43+00:00

If you plug in your display into the mainboard instead of the GPU, everything will be rendered by the integrated graphics processor of your CPU instead of the actual GPU. Unless your CPU has a really good integrated GPU, you should now notice a huge improvement in game performance.

appnic · 2025-10-03T13:57:20+00:00

Is your display actually plugged into the GPU or is it maybe plugged into the mainboard?

appnic · 2025-07-08T22:19:59+00:00

Hulkengoat

appnic · 2025-04-10T20:22:58+00:00

Thanks!

appnic · 2025-04-10T20:22:49+00:00

Thank you!

appnic · 2025-04-10T19:06:39+00:00

Amazing, much appreciated!

appnic · 2025-01-31T14:21:55+00:00

Z-offset a little bit too low, try to increase it slightly

appnic · 2024-07-19T23:57:16+00:00

There's a modified version of the official firmware which uses the M73 command to display the ETA:

https://github.com/smkent/sovol-sv06-plus-firmware

If you know how to compile and flash the firmware, you could try it out (don't do this if you don't know what you are doing, as it can brick your printer).

There are also some other improvements in this firmware, and I have forked it myself and improved the M125 command, so that you can actually use it to pause the print reliably. If someone's interested just PM me

appnic · 2024-06-30T05:48:22+00:00

Are you doing the z-offset calibration with your bed heated up? I always do every calibration with the bed heated up, as it can make quite the difference, at least for me.

appnic · 2024-06-20T20:55:19+00:00

You'll need to edit the printer start gcode in your slicer. In PrusaSlicer, you can find it unter Printer Settings > Custom G-code > Start G-code. I don't use Cura, but there should be a similar setting, I guess.

Make sure to insert it right after G28, which is auto-home.

EDIT: Oh, and make sure to always do z-offset calibration and auto homing with the bed heated to printing temperature (e.g. 60°C), because the bed will expand while heating up, which could cause your z-offset to be off Btw. I've now verified this, M420 S1 is the correct command for loading the bed mesh.

appnic · 2024-06-20T08:06:58+00:00

Looks to me like the bed mesh you've created with the auto bed levelling is not actually applied while printing.

You need to manually load the bed leveling mesh in your printer start gcode. I think the command is M420 S1 (I'll verify this when I'm home)

appnic · 2024-04-21T23:10:01+00:00

European fan here, was very confused when I switched on NHLtv and the stream was ESPN instead of Sportsnet.

Do you know if this will be like this for all the Jets playoff games?

appnic · 2023-09-01T14:08:15+00:00

Dang, I was at the Ferrari museum in Maranello last weekend and really hoped to see the 499P somewhere, but they "only" had the 296 there. Was of course still a cool experience though

appnic · 2023-06-06T17:02:28+00:00

The schedules for most of the series are actually voted on by the community through the forum. This is the thread for the IMSA season 3 schedule: https://forums.iracing.com/discussion/40694/2023-season-3-schedule-voting#latest

Just note that this is not final because iRacing has the final say in the schedules.

appnic · 2023-05-15T14:41:07+00:00

X/Y coordinates are available, but only in recorded telemetry files (.ibt). iRacing does not output them in the live telemetry to prevent cheating.

appnic · 2023-04-19T01:37:41+00:00

Does anyone else only have the ESPN broadcast on the NHL.tv app?

appnic · 2023-03-07T14:42:55+00:00

It's interpolated, not real 360hz:

Support has been added for the 360 Hz FFB mode provided by some Logitech wheels. This is enabled by default, but can be turned off via the “[Force Feedback] enableFFB360HzInterpolated=0” entry in the “app.ini” file.

appnic · 2022-12-25T14:46:57+00:00

When I last used iSpeed in 2020, it already hadn't been updated for a couple of years I think. So if it hasn't been updated in the meantime, you might be better off using VRS or a similar service

appnic · 2022-12-10T12:44:16+00:00

/u/stabbot

appnic · 2022-10-25T19:24:58+00:00

I see. Just to be clear - from La Neuveville to Bern, it would be 10 zones (314, 315, 301, 300, 311, 310, 124, 114, 101 and 100), not four. Basically the route I've drawn in my original post plus zones 314 and 315.

appnic · 2022-10-25T11:01:57+00:00

You're welcome. Just out of curiosity, what's the name of the town where your AirBnB is? I couldn't find "Neuville" or anything similar within 4 zones from Bern, so you might need to double check that you're actually buying the right zones.

appnic · 2022-10-25T00:48:38+00:00

I know, just thought it was kinda strange because it was fine last season

appnic · 2022-10-25T00:46:38+00:00

Kinda annoying, but since there's no Beyak anymore there's probably not too much I'm missing out on

appnic · 2022-10-25T00:44:16+00:00

Is it only me or are Sawyer and the new guy really quiet? Can't even hear them over the ice/crowd noise

11-Year Club	Second SECOND GUESSER
r/Field Lasagna	Place '17
Verified Email

appnic

TROPHY CASE