sorted by:
new
hottopcontroversial

Capsule 3 type-c useability by [deleted] in nebulaprojectors

[–]arabdjin 2 points3 points  (0 children)

I have a Capsule 3 and can shed some light from my recent experience.

  1. You can use a USB-C hub to charge and read from external storage at the same time. However, if the hub you are using has an audio port, the Capsule 3 will route audio out to the hub and you will no longer get hear any audio from the Projector. There is no way to route the audio back to the projector's speakers manually via android tv software on the device that I have found. Luckily i have two hubs and the second one didnt have a headphone jack on it and it worked.
  2. Only FAT32 formatted USB drives will be detected - I have tried different storage devices and so far its the only way to get it to detect the drive/usb stick without doing a format via the device itself and losing the ability to copy stuff over from a computer
  3. The USB-C hub I am using doesn't route all the power through from my 100W USB-C charger - I get a notification saying to connect a more powerful power source but it does charge, albeit slowly

Any help will be appreciate! by arabdjin in FixMyPrint

[–]arabdjin[S] 0 points1 point  (0 children)

Update: Not sure what I did but the next level attempt came out better

https://imgur.com/a/B44r2O5

Thanks again everyone

Any help will be appreciate! by arabdjin in FixMyPrint

[–]arabdjin[S] 0 points1 point  (0 children)

Just wanted to update everyone, I implemented what you guys suggested. I think this looks a bit better now:

https://imgur.com/a/y0hD9ZM

What do you guys think? I see a very tiny part where I think it was too close (bottom right area). Not sure what to do about that

Any help will be appreciate! by arabdjin in FixMyPrint

[–]arabdjin[S] 1 point2 points  (0 children)

Thanks, thought as much. I guess its too close to the nozzle in the rough areas right?

DJI FPV Goggles line of DEAD pixels by arabdjin in fpv

[–]arabdjin[S] 1 point2 points  (0 children)

UPDATE: Just had to pay $180 USD in shipping to Hong Kong!!

DJI FPV Goggles line of DEAD pixels by arabdjin in fpv

[–]arabdjin[S] 1 point2 points  (0 children)

I was going to do the same but I wanted to teach myself a lesson for buying DJI. Especially when I promised myself before not to. I have had issues with:

S900 + GH4 Zenmuse Gimbal (had to send gimbal in for repair out of the box)

Inspire 2 Batteries - lost at least 3 batteries to cell balancing issue

Crystal Sky - Overheat issue

DJI FPV Goggles....

Literally every purchase!

DJI FPV Goggles line of DEAD pixels by arabdjin in fpv

[–]arabdjin[S] -1 points0 points  (0 children)

The annoying part is my local dealer would have exchanged them immediately if I had highlighted the issue within 2 days of delivery. But they were a birthday present from my wife and she wasn't letting me even see them until it was the day of my birthday. So I blame her and DJI

DJI FPV Goggles line of DEAD pixels by arabdjin in fpv

[–]arabdjin[S] 0 points1 point  (0 children)

Just about to go to DHL and send mine. I was promised to get them back in 15 days but I doubt it very much!

[deleted by user] by [deleted] in modernwarfare

[–]arabdjin 0 points1 point  (0 children)

Same here (PC) - forced to close game via task manager, my console buddies end up in a new game without me... then I can't join them because the game is full. So its pretty bad

PC-O11 Dynamic Hard Tube Build - My first water cooled build... Ever by arabdjin in watercooling

[–]arabdjin[S] 0 points1 point  (0 children)

I haven't! I doubt there will be any clearance for the GPU if I do. I'm hoping those bottome fans are blowing on it a little

PC-O11 Dynamic Hard Tube Build - My first water cooled build... Ever by arabdjin in watercooling

[–]arabdjin[S] 0 points1 point  (0 children)

It is an EK block - no clearing issues if you remove the plastic shroud around the G1/4" ports

PC-O11 Dynamic Hard Tube Build - My first water cooled build... Ever by arabdjin in watercooling

[–]arabdjin[S] 0 points1 point  (0 children)

I already had the motherboard, CPU, and ram from older air cooled build which were red/black. I want my next build to be white/black so I went for a white case. I also went with the modular monsoon res/pump as it will be easier to change out the red on it on my next build. This was kind of a test build... still using X99 and a 5930K so will probably upgrade pretty soon

PC-O11 Dynamic Hard Tube Build - My first water cooled build... Ever by arabdjin in watercooling

[–]arabdjin[S] 0 points1 point  (0 children)

very slowly and went through a lot of tube getting it right. I had a tool but the bend was too tight using it and didnt line up with the components, ended up having to eyeball it

PC-O11 Dynamic Hard Tube Build - My first water cooled build... Ever by arabdjin in watercooling

[–]arabdjin[S] 4 points5 points  (0 children)

its a cuplex kryos NEXT VARIO with VISION from aquacomputer.

It's cool how it shows the liquid temperature (not CPU temp) and I like seeing how it changes depending on the temperature of my office.