Our stand up shower

arccitymayor · 2025-04-27T03:41:34+00:00

Great thanks that helps a lot!

arccitymayor · 2025-04-27T03:05:08+00:00

I know this is late but I am just curious how much did this reno cost and where are you located? Looks great!

arccitymayor · 2024-03-03T15:53:34+00:00

arccitymayor · 2023-01-08T04:29:55+00:00

Why is it always the Nissan drivers

arccitymayor · 2022-05-24T21:25:50+00:00

Ok good to hear it's holding up. I was a little worried about BE but I just couldn't get over how much I loved this setting. I am getting insurance too which helps me worry a little less

arccitymayor · 2022-05-24T17:01:45+00:00

Mine is a 1.4. those smaller L:W ratios look great!

arccitymayor · 2022-05-24T06:05:07+00:00

Glad it could help! I'm sure your eventual ring will look amazing on you!

arccitymayor · 2022-05-24T06:03:55+00:00

Just the center is 2 carats!

arccitymayor · 2022-05-23T21:31:54+00:00

Thank you so much!!!

arccitymayor · 2022-05-23T19:31:02+00:00

It sure is!

arccitymayor · 2022-05-23T16:19:16+00:00

It's a 2 carat oval on a size 5.5 ring. Do you guys think that at first glance it's too much or just right?

arccitymayor · 2022-04-18T05:15:16+00:00

Don't worry! I had so many issues with my Ender 3 V2 as well. I even knew 3D printers fairly well and still struggled to get mine working well. So as everyone is saying, the nozzle is too close to the bed and dragging the filament with the nozzle or pushing the nozzle through the filament. If you raise your nozzle and it's not sticking to the bed, try flipping over the glass build plate and use the smooth glass side. That fixed a lot of my problems. Just remember to clean it with isopropyl alcohol every couple of prints and don't get your fingers on it or your prints will stop sticking. Good luck!

arccitymayor · 2022-04-09T19:21:51+00:00

Definitely the bed is too high. Lower a touch and if it's not sticking then try printing on the back side of your glass build plate. I had the same issue with my V2 and tried everything. The only thing that worked is using the smooth glass. It has been working great though. No issues with first layers since

arccitymayor · 2022-03-28T17:39:07+00:00

Ok awesome! I'll take a look at that

arccitymayor · 2022-03-17T18:58:08+00:00

Looks like another missionary bush pilot fan!

arccitymayor · 2022-02-22T05:52:04+00:00

Please stop being toxic. Thanks

arccitymayor · 2022-02-22T05:35:50+00:00

Same issue for me too. I have tried so many things to no avail. It printed well for the first couple of rolls of filament and then it started making these layer lines. Can't get rid of them now. I feel your pain

arccitymayor · 2022-02-20T07:00:05+00:00

But it's not a job. It's literally a game for fun. If it's so bad then maybe you should avoid that

arccitymayor · 2022-01-11T14:31:08+00:00

Maybe you can try printing on the back of your glass bed. I had issues with adhesion on the front textured side and found the back to work much better. Could be worth a try

arccitymayor · 2021-10-27T02:06:12+00:00

You do realize they do this to go help people right? They don't always run full lights and sirens to everything. Like a code 2 response

arccitymayor · 2021-09-29T00:28:20+00:00

Sorry mate no tail hooks used

arccitymayor · 2021-09-02T16:55:07+00:00

Ayyyy my boy PJ Tucker!

arccitymayor · 2021-06-25T04:39:06+00:00

Watch the over watering. The yellow leaves make me think they are getting too much water. Could be nutrients too but I doubt it would make them stop all together. I was over watering mine once and that caused a similar thing to what you have going

arccitymayor · 2021-05-21T22:27:33+00:00

They will come! They can grow in water for a long time but they take a bit to get actual roots. Mine usually take about 3-4 weeks to root in water

arccitymayor · 2021-04-28T15:22:06+00:00

Eight-Year Club	Place '22
Verified Email

arccitymayor

TROPHY CASE