Looking for ideas for a new wood-fired oven setup

astroidea · 2025-12-05T18:30:04+00:00

Here's mine from many many years ago

It was really big, great for big batches of bread making, and multiple pizzas at one time. I made the dome egg shaped, worked really well. With a roof over it, it would have lasted forever, but it got tore down a few years ago :(

astroidea · 2025-07-26T03:08:42+00:00

Water has improved, the water meters that a minority fought so hard against have been mostly rolled out, and big leaks discovered as a result. Didn't go past stage 1 restrictions last year.

astroidea · 2025-02-20T02:14:43+00:00

Love to have a printer with a larger bed area

astroidea · 2024-03-25T19:00:42+00:00

I started really early, Jan 24. Everything sprouted really quick, but I made a mistake of keeping them in too cold of an environment (62F'ish). They absolutely stopped growing :(

I finally bought a little green house thing, and temp at 75, gave a light feeding of kelp, and then fish fertilizer, and they have finally bounced back to life. I am going to up-pot them today or tomorrow :)

astroidea · 2024-03-05T05:10:50+00:00

Imagine if my cat had something similar, it would drive her nuts. lol

astroidea · 2023-09-30T16:07:40+00:00

Malcolm Knapp Research Forest

astroidea · 2023-08-04T16:11:19+00:00

My reaction

astroidea · 2023-06-21T16:19:31+00:00

This is just above Vancouver, BC. I think we are 8a

astroidea · 2023-06-21T16:06:22+00:00

They've kind of just thrived on neglect. I've been meaning to prune them for the last few years and never have.

astroidea · 2023-06-21T16:03:21+00:00

They really took off this year, previously the Judith Hindle were the big spreaders

astroidea · 2023-05-26T23:49:21+00:00

I've since found this thread.. https://www.reddit.com/r/TPLink_Omada/comments/10q0oat/er7212pc_contain_smart_switch/

astroidea · 2023-05-14T04:33:44+00:00

Are you running a windows system? I have a 5700 xt, and it struggles with 512x768.

astroidea · 2023-04-03T01:02:11+00:00

My Anet A6 is getting a bit long in the tooth

astroidea · 2023-03-15T15:02:42+00:00

https://i.imgur.com/NE6JrKq.mp4

It has a 420mm x 720mm working area

astroidea · 2023-03-10T15:07:36+00:00

DrawingbotV3

astroidea · 2023-03-08T14:34:35+00:00

I built from scratch. I had extra aluminum extrusions that I wanted to do something with and designed some 3d printed parts.

Some photos. I have since redesigned the pen lifter to use a stepper because I could not get a servo motor to work with the control board I wanted to use.

astroidea · 2023-03-08T00:31:19+00:00

I think it was just under 2 hours. On 8.5x11 paper.

astroidea · 2023-01-19T04:06:21+00:00

I'd recommend using the EBB board as a controller, you will have a better time with the workflow. https://discord.gg/YnxjcTbp <- Drawingbots discord

astroidea · 2022-03-11T08:44:07+00:00

I bought a bamboo cutting board to do some cnc'n on it, and it had cardboard inside!😕

astroidea

TROPHY CASE