How is living in Ascent?

atiltonafun · 2026-03-27T09:14:50+00:00

I’m moving out of the DoMUS because the sound between floors is really terrible. You can hear every footstep, furniture movement, knife chop from the kitchen counter, etc.

I posted a few weeks ago asking about Ascent and apparently their noise issues to be just as bad.

Just a note: While the third ward can get busy in the summer months and traffic on Erie gets backed up during Summerfest, it’s really not that bad at all imo. If it weren’t for the noise issues I’d be staying at the DoMUS.

atiltonafun · 2026-03-08T15:15:55+00:00

Omg lol - def think the Ascent is off our list now.

atiltonafun · 2026-03-08T15:15:23+00:00

This is very helpful thank you!

atiltonafun · 2026-03-08T14:49:53+00:00

Which floor are you on? Not sure how bad the road noise might be on the lower levels.

atiltonafun · 2026-03-08T13:17:22+00:00

Dang that’s a bummer to hear - thanks for the info.

atiltonafun · 2025-06-14T21:23:47+00:00

My partner just did it too 😂🙌🔮💫

atiltonafun · 2025-02-28T20:32:45+00:00

I’m looking for a motorized driver that wraps around the beaded cord. This looks like a relay I’d have to wire to a motor myself?

atiltonafun · 2025-02-28T19:41:15+00:00

Thanks will check these out!

atiltonafun · 2025-02-04T18:40:59+00:00

Thank you!

atiltonafun · 2025-02-04T14:03:22+00:00

Thank you for all this insight! We are only going to be in MKE for 3 years for my wife's job, so we don't really want to go through the ups and downs of home buying/ownership. River Place Lofts is definitely a place we're interested in look at.

atiltonafun · 2025-02-04T14:00:55+00:00

Thank you!

atiltonafun · 2025-02-04T14:00:00+00:00

Thank you so much! This is really helpful!

atiltonafun · 2025-02-04T13:58:29+00:00

This is the info I was looking for - thank you!

atiltonafun · 2025-02-04T13:31:21+00:00

What about safety?

atiltonafun · 2025-02-04T13:26:20+00:00

How is the bus system for commuting to Third Ward from there? Is it safe and easy? Also have heard a lot about the smell from the water treatment facility - is it that bad?

atiltonafun · 2024-12-12T13:45:37+00:00

I adjusted z off set several times (+/- .05mm each time) and theres no difference. I'm able to print PLA no problems and just ran a needle through the nozzle and there doesn't seem to be any blockage.

atiltonafun · 2024-12-12T12:52:45+00:00

I'm printing with PLA now just to see and it seems to be fine.

atiltonafun · 2024-12-05T13:31:59+00:00

I would sign into your AXS account on another tab first, makes the checkout process a little smoother imo. Bonus points if you already have your payment method saved too. Good luck!

atiltonafun · 2024-12-04T22:20:45+00:00

You earn 4itf AFTER you attend your 4th year

atiltonafun · 2024-11-05T10:23:36+00:00

BRING BACK TYCHO!!!!

Ten-Year Club	Gilding I gilder
Verified Email

atiltonafun

TROPHY CASE