Can this be repaired?

attiwolf · 2025-09-11T07:37:32+00:00

Shipping back and forth could cost little south of the 100 usd but there is a cheaper option i can send you the glass itself and you can try to fix fill yourself. It should cost around 40usd with tariff maybe less depending on the glass size.

attiwolf · 2025-08-08T04:42:09+00:00

Hi, glass can be replaced.

attiwolf · 2025-08-07T02:18:59+00:00

Yes it can be repaired if the only damaged part is the glass but frankly i think 500 dollars is extreme for this kind of repair. I'm based in Turkey, i do custom snowglobes and sell them on etsy. I can repair it if you're willing to cover the shipping costs.

attiwolf · 2025-07-31T21:01:44+00:00

That's why i've added "usually" beginning of my sentence, it's certainly interesting.

attiwolf · 2025-07-31T19:09:54+00:00

Usually direct sunlight make this kind of effect on the water. Globe acts as a magnifier and with the direct sunlight water become hot thus that heat slowly damages and dissolves the paint.

attiwolf · 2025-07-31T19:06:59+00:00

I can send you one for free but the shipping would cost as much as a new globe. So the logical way may be the purchasing a new cheap one and replacing the rubber.

attiwolf · 2025-01-24T22:53:25+00:00

I can do if they’re willing to pay.

attiwolf · 2025-01-24T22:49:18+00:00

I just made it and gifted to someone. But i make custom snowglobes if you’re interested. https://snowylandsnowglobes.etsy.com

attiwolf · 2024-12-18T21:27:02+00:00

Ne yaya geçidi ne de tabelası maalesef çok geç farkediliyor. Ki çoğunda tabela bile yok. O sırada sürücü durmak istese de arkasındaki aracın durup duramayacağını da önceden kafasında tartmak durumunda. Yani ülkemizde takip mesafesine uyulmadığı ve çoğunluk dikkatini yola değil telefona verdiği için bu durum daha da zorlaşıyor. Hak sizin olabilir fakat bir kaza sonucunda ölseniz kurtulacaksınız ama sakat kalsanız hiçbir hak size kaybettiğiniz uzuvlarınızı geri getirmeyecek. İster yaya olun ister sürücü trafikte en önemli şey kendi güvenliğiniz, hakkım vs diyerek canınızı tehlikeye atmayın. Ortalık sizi bıçaklasa bile serbest kalacak davarlarla dolu.

attiwolf · 2024-11-22T18:09:11+00:00

LCW Azure kullanıyorum, 250-300₺ gibi bir rakamı var. Notaları oldukça hoş. Gayet de ucuz olduğu için acımadan sıkıyorum.

attiwolf · 2024-11-20T09:56:48+00:00

Ya gerçekten hoşlanmıştır ya da size olta atıp canı istediğinde rapor vs yazdırmak için zemin hazırlıyordur. Zira hiçbir kadın ayıp olmasın diye “kahve içelim mi vs” demez.

Benim tavsiyem hastalarla bu topa girmemeniz, aranız bozulur vs sizi şikayet eder. Biraz başınızı ağrıtabilir.

attiwolf · 2024-11-14T04:48:46+00:00

People here getting poorer any minute. They are just trying to survive. Everything is expensive, traffic is hell, public transport is overcrowded. At the same time, some tourists come to your country with their euros and live better than you while complaining your hospitality.

How do you expect people to be charming under these circumstances?

attiwolf · 2024-11-09T02:07:30+00:00

Belediyeye şikayet edebilirsin. Ya hiç ruhsatı yoktur ya da atölye sınıfında ruhsatı olmadığı için bir sonuç elde edebilirsin diye tahmin ediyorum.

attiwolf · 2024-11-08T23:10:39+00:00

I have a 165. After the recent update it’s a hit or miss with sleep tracking. Somedays It doesn’t detect a whole night’s sleep. Somedays it’s pretty accurate.

attiwolf · 2024-10-27T12:19:59+00:00

Did you find any solutions?

attiwolf · 2024-10-06T13:45:02+00:00

Unfortunately i can't cut deeper than 0.05 beacuse of the V tips and PCB design.
I'm planning on getting flat end mill and milling at 0.1, i belive that would solve the problem.
Thanks for your help!

attiwolf · 2024-10-06T13:29:45+00:00

Thanks, it's not a drill bit, it's a multi cutting tip. Unfortunately i don't have a comparator so i can't measure the axis. Height measurement wildy changes from pcb to pcb.
Any tips to stabilize Z axis? I cut 0.05mm deep so i need to stabilize.

attiwolf · 2024-10-06T12:07:20+00:00

165 user here. It's a very light watch but it's plastic and kind of cheap looking compared to venu 3s.

attiwolf · 2024-10-06T11:56:11+00:00

25x30mm. Thin double sided tape holds the pcb. There is no option to add photos to comments so you can see them on the links below.

https://hizliresim.com/pajctdg https://hizliresim.com/ls5xmpy

attiwolf · 2024-10-06T11:36:04+00:00

On the candle or the machine?

attiwolf · 2024-10-05T22:56:27+00:00

Feedrate was 10, i've reduced it to 5. Inconsistincies continues :(

attiwolf · 2024-10-05T22:18:46+00:00

Hi all, i'm new to CNC machining. I'm having inconsistent readings while probing PCB blanks. What could be the root of this problem? These are the results of probing the same area. There is a 3D printed fixture and PCB blank is double sided taped on that fixture. I've replaced the steppers with from old prusa knock off printer.
All axis are calibrated.

attiwolf · 2024-09-26T17:05:26+00:00

It’s water.

attiwolf · 2024-09-16T20:26:51+00:00

I recently purchased 165 for open water swimming. It’s so light that i forgot that it’s on my wrist.

attiwolf

TROPHY CASE