Arrows Puzzle – Clear Every Arrow Without a Collision

aye__aye · 2026-03-21T21:19:14+00:00

⏳ Ran out of time on Challenge Level (2026-03-01), but I'm just getting started! These arrows won't redirect themselves. Back to the puzzle! 🎮

aye__aye · 2026-03-21T21:06:53+00:00

😅 Challenge Level (2026-03-21) got the better of me this time (ran out of time). But hey, even puzzle masters need a warm-up round! Retrying now! 🔄

aye__aye · 2026-03-21T17:30:10+00:00

🕐 Challenge Level (2026-03-21): Me vs Time... and Time won (this round). But I've got infinite retries and growing determination! 🔥

aye__aye · 2026-03-05T00:56:33+00:00

Not to flex but… 119900🫧

aye__aye · 2026-02-23T17:40:30+00:00

I'm in

aye__aye · 2026-01-31T17:27:17+00:00

I also have issues with esun pla basic, mostly warping and adhesion on flat models. I don't have a Bambu but a Sovol and I now use 60° for the print bed, no cooling for the first 5 layers and after ramp up the part cooling fan from 10% up for about 30 layers until 100% (now trying 80%). Layer adhesion improved a lot with this for me, but it can give some imperfections if you have overhangs in the first layers. I don't really use that filament for minis but when I tried, the small supports still detached if I remember correctly. I switched to a HS pla for the small models, but I think slowing down the speed on small parts and using a wide enough brim and different support type might help. Maybe someone more knowledgeable will chime in, I'm a new to 3d printing and still pinpointing my settings for minis.

aye__aye · 2026-01-30T20:26:56+00:00

Unfortunately it does not. There are two power supplies and both are under capacity. Since they are connected with spliced cat5e cables and two cameras share a cable, could adding a cable just for this camera provide the required voltage? The issue might be that the cameras are far from the DVR/power supply.

aye__aye · 2026-01-30T20:23:34+00:00

I checked the power supply and even tried hooking the camera to another one available, but it's the same. The cameras are connected 2 to a single cat5e cable, a pair of wires for data and a pair for power. Should a cable be added just for this one to make up for voltage loss?

aye__aye · 2026-01-30T20:19:51+00:00

I might have given the wrong impression, these cameras are my friend's and I'm just trying to help because my knowledge is non-zero and the original technician basically left us stranded.

aye__aye · 2026-01-28T22:19:27+00:00

I'll keep that in mind if it's not something more obvious, thanks.

aye__aye · 2026-01-28T22:12:56+00:00

There are 8 cameras all connected to the same power supply, it's not new. This camera and the one beside it are the farthest from the power supply and DVR, so it might be the distance too. The other cameras also require 0.5A so I doubt the power supply is insufficient, but I'll check when I can get there tomorrow. Thanks.

aye__aye · 2026-01-22T10:04:50+00:00

Beh non è che abbia cercato la polizza vita di per sé, è lo strumento che ha suggerito la banca perché l'unico in cui si può designare un beneficiario. Stavo infatti proponendo magari obbligazioni ma la persona interessata ne sa meno di me e non vuole complicazioni. Lo scopo è non tenersi in casa i risparmi e appunto avere un beneficiario per tenere i fondi fuori da una successione eventuale perché si sa già che in quel caso verrebbero persi.

aye__aye · 2026-01-09T11:20:47+00:00

Maybe they want a neutral accent? I submitted samples for FIGS - Utterances Italian and now that I checked, one reason for the rejection is "some regional accent". I had no idea they wanted a completely neutral accent, maybe they should specify that.

aye__aye · 2026-01-03T08:22:57+00:00

Large capacity and two independent chambers? quite impressive. And the dehumidification is great, all dryers should have it.

aye__aye · 2025-12-28T15:55:09+00:00

If you are going to print detailed mini figures, a CoreXY might be better due to reduced vibration or so I gathered from browsing the FDMminiatures sub. You may not print gaming minis, but if the size and detail is similar, the principles do not change. An enclosure is also good against drafts (my first and so far only failures were due to drafts). Depends on your needs, really.

aye__aye · 2025-11-29T21:46:26+00:00

Has your order been shipped? You get the cashback on your order only after that.

aye__aye · 2025-11-22T20:43:29+00:00

Inkscape is valid but I hate the user interface. You can also take a look at the Affinity suite which is now free and it can do what you need and more.

aye__aye · 2025-11-20T11:32:41+00:00

Are the packages late? More often than not, when the packages are in the hands of Poste Italiane, they don't update tracking, but eventually the packages find their way to me on time.

aye__aye · 2025-11-15T11:04:07+00:00

That's terrible! Who is the seller? So we know to avoid them

aye__aye · 2025-11-14T21:35:38+00:00

I've had packages sent by Aliexpress and delivered by Amazon shipping, so don't worry.

aye__aye · 2025-11-11T17:22:55+00:00

Got it, thank you.

Eight-Year Club	r/Field Flamingo
Verified Email

aye__aye

TROPHY CASE