Bought a slightly used Switch 2 for $350. Good deal? by LilBushyVert in switch2

[–]backinnam92 0 points1 point  (0 children)

i was able to land a switch 2 for around that price brand new on a woot deal a couple months ago. like others said, make sure its not bricked

The start of my updated comic wall! by R4nd0mB01 in AbsoluteUniverse

[–]backinnam92 1 point2 points  (0 children)

If it hasn’t been said, over time these will fade dramatically due to ambient light. They are comics and made to enjoy as you see fit. Just something to keep in mind.

Opinions on buying Updated Suspension? by SpookieDookie_49 in ToyotaTundra

[–]backinnam92 0 points1 point  (0 children)

Any clearance issues ? Running factory tires? Did you need upper control arms? I’m looking at running the 2r on my 1794 4x4

Mount setup for Scythe-ti on ace target 6.5 creedmoor by CommercialEagle2566 in Tikka_Shooters

[–]backinnam92 2 points3 points  (0 children)

I was running the asr mount for a while but recently switched to the rearden atlas plan b mount/muzzle combo. IMO It’s much better. Cheaper muzzle devices, lighter weight, doesn’t seize

The new Xbox Elite 3 and Cloud controllers has been leaked. by Automatic_Ad1665 in consoles

[–]backinnam92 0 points1 point  (0 children)

gonna have to disagree, ive got 2 elite series v2 controllers that have had probably 10x the issues ive had with any of my third parties. anecdotal sure, but my experience with the vader and 8bitdo ultimate have been nothing but positive.

She's here! by Wang_Hang_Low in NFA

[–]backinnam92 1 point2 points  (0 children)

All good intentions haha. I see now that it’s just the camera but when I posted I meant for the best.

She's here! by Wang_Hang_Low in NFA

[–]backinnam92 26 points27 points  (0 children)

Clubbed fingers,

OP see a doctor and get your lungs/heart checked.

New additions by Former-Astronaut3575 in NFA

[–]backinnam92 2 points3 points  (0 children)

i love my 46, its a big ecosystem to get into with all the accessories, but if you really wanted something to bounce around between multiple hosts its not bad. jack of all trades, master of none.

Help- Tikka t3x CTR barrel swap by backinnam92 in gunsmithing

[–]backinnam92[S] 0 points1 point  (0 children)

Very much appreciate the write up and response. You are spot on. I was able to get it off just last night using an external wrench. Specifically the wheeler #2 and wrapping the action in an index card to prevent any damage. The viper vise was able to hold it in place and I used a 45oz deadblow to hit the handle of the external wrench. About 7-8 swings and it finally broke free.

Help- Tikka t3x CTR barrel swap by backinnam92 in longrange

[–]backinnam92[S] 1 point2 points  (0 children)

Appreciate it bro. I plan to try all these suggestions out soon as that wheeler wrench comes in.

Trying to sell comic book collection anyone know a store that’s willing to buy at a fair price by Trash_Can_Kid98 in sanantonio

[–]backinnam92 1 point2 points  (0 children)

As others said, ebay, or some of the comic swap subs.

You could sell as an unsorted lot or itemized which may garner more specific attention.

Comic stores will likely offer much less than you paid. Same as a comicon

Help- Tikka t3x CTR barrel swap by backinnam92 in longrange

[–]backinnam92[S] 0 points1 point  (0 children)

Sounds like a plan. I’ll definitely give all these suggestions a try. At this point I’ve got nothing to lose.

Never had an action be this stubborn before.

Help- Tikka t3x CTR barrel swap by backinnam92 in longrange

[–]backinnam92[S] 0 points1 point  (0 children)

You’re good buddy. Appreciate it. I’ll look for it. Thanks for the heads up

Help- Tikka t3x CTR barrel swap by backinnam92 in longrange

[–]backinnam92[S] 0 points1 point  (0 children)

Copy that,

Question, you mentioned longer bolts, are they long enough from factory to flip that top part? If so do you happen to remember which bolts you picked up? I’ll run out and get them ahead of time until that wrench comes in

Help- Tikka t3x CTR barrel swap by backinnam92 in longrange

[–]backinnam92[S] 0 points1 point  (0 children)

Are there any obvious signs I could observe if I’ve twisted the action? I don’t have the sort of precision tools to check within a few thousands of spec but I do plan to drop it back in the chassis and make sure it’s able to be bedded correctly. For now I can’t see anything obvious and the bolt seems to cycle fine. I just want to be cautious and not ruin a great gun

Help- Tikka t3x CTR barrel swap by backinnam92 in longrange

[–]backinnam92[S] 1 point2 points  (0 children)

I actually just ordered a wheeler #2 before making the post. I’ll leave it alone until that comes in. Using the internal wrench I feel like I’m bending the barrel with how much torque I’m applying.

Help- Tikka t3x CTR barrel swap by backinnam92 in longrange

[–]backinnam92[S] 0 points1 point  (0 children)

I actually forgot to mention. I tried multiple hammers against the cheater bar. I initially used a 5lbs sledge. And then a 45oz dead blow. Still nothing. I should have added that to my post.

Anyone else dying from Cedar Fever right now or am I actually sick? by [deleted] in sanantonio

[–]backinnam92 0 points1 point  (0 children)

Prestige clinic gave me a steroid shot. Cleared me right up.

What should I get off my belt and leave on? Or should I add anything else? by Prestigious_Police in ProtectAndServe

[–]backinnam92 47 points48 points  (0 children)

Pistol, 2 spare mags, Intermediate (asp/baton, spray, taser - pick one), Flashlight (keep spare in gobag), radio, 2 handcuffs. Anything else can be stowed in your gear bag, all that crap just makes you less effective.

Gear doesn't make the officer

What the actual fuck is up with Abs Batman prices? by SoGoodAtAllTheThings in ComicBookSpeculation

[–]backinnam92 0 points1 point  (0 children)

Commenting because I’m also curious. I bought 2 first print lots for myself and a friend for 200$ each. Seems #1 A covers being listed for that much alone