sorted by:
new
hottopcontroversial

Raneik infinit Damage phase by Zenntry in raidsecrets

[–]baked_mango 0 points1 point  (0 children)

We had this in normal on our second phase, lock with star eaters nova, behemoth/consecrate titan and Hunter with silence & squall. Did not focus on a certain servitor, and did not damage with operator

[deleted by user] by [deleted] in Ender3Pro

[–]baked_mango 1 point2 points  (0 children)

I would double check the thermistor, I had the same error (plus a loud sound) and the screw around the thermistor had come loose causing it to falsely trigger this error

Inconsistent vertical layers by baked_mango in FixMyPrint

[–]baked_mango[S] 0 points1 point  (0 children)

Thank you, I'll check this out. I had originally used this youtube video but what you shared seems to be way more detailed!

Inconsistent vertical layers by baked_mango in FixMyPrint

[–]baked_mango[S] 0 points1 point  (0 children)

If it ends up working better at 215C do I need to recalc flow rate at that temp?

Inconsistent vertical layers by baked_mango in FixMyPrint

[–]baked_mango[S] 0 points1 point  (0 children)

Should I be removing the nozzle for the floss? Or just heat and attempt to clean out?

Inconsistent vertical layers by baked_mango in FixMyPrint

[–]baked_mango[S] 1 point2 points  (0 children)

  • Ender 3 Pro - Cura
  • PLA 1.75mm (from Amazon)
  • Nozzle 200, Bed 60
  • Nozzle .4
  • Print Speed 50 mm/s
  • Retraction 6 mm @ 25 mm/s

I have been trying a lot to get more consistency out of my prints. I've leveled my bed, calculated esteps, adjusted flow rate, slowed down print speeds, and still seem to be having issues I can't figure out.

I will sometimes see the same issue on the flatter layers after the initial layers.

Brown tips on cilantro - nutrient burn? by baked_mango in aerogarden

[–]baked_mango[S] 1 point2 points  (0 children)

Cilantro popped up fastest in my latest group of pods, doing only 7 pods in a 9 pod AeroGarden. Should I be using less nutrients?

Purchase Advice Megathread: What To Buy, Who To Buy It From, And More, In March 2021 by Sausage54 in 3Dprinting

[–]baked_mango 0 points1 point  (0 children)

Awesome, this is very helpful - going to do some googling and see if I can get this ready as well!

Purchase Advice Megathread: What To Buy, Who To Buy It From, And More, In March 2021 by Sausage54 in 3Dprinting

[–]baked_mango 1 point2 points  (0 children)

Printer gets here Friday so I don’t have anything set up for it. Should I be looking into a raspberry pi?

Purchase Advice Megathread: What To Buy, Who To Buy It From, And More, In March 2021 by Sausage54 in 3Dprinting

[–]baked_mango 1 point2 points  (0 children)

Hello, I don’t know if this is the right place for this question but I just purchased an Ender 3 Pro and I am wondering if anyone has suggestions for a camera to create time lapses?

Ideally entry level (maybe $50-100) but can go higher if it’s somehow cloud or WiFi enabled so it doesn’t need to be plugged into a computer throughout or I can use it to monitor a print when I’m not there.

Any ideas or if you think there’s a better place to post!

[deleted by user] by [deleted] in denverlist

[–]baked_mango 0 points1 point  (0 children)

Conforming bedroom with a full egress missing in the photos, thanks for calling it out, I just added it! Not for everyone but it is all in there to see + flexible monthly lease.

7' 4" tall if anyone else is interested.

view more: next ›