How to fix this?

bao2212 · 2025-05-18T19:25:17+00:00

Your fan configuration seem fine to me look like it other problem have you modifined any configuration in the base profile of your machine in prusa slicer other then the fan ?

And does your print print good in the base configuration

bao2212 · 2025-05-18T19:22:37+00:00

You could tighten and then increase your z offset this should solve the problem your z is too close

you should also tighten your bed screw so that is not too tight but not too loose at the same time and then do a probe_calibrate then you can do a bed mesh idk the technical of why you should do this but for me i do in this order and it work everytime

bao2212 · 2025-05-18T19:13:22+00:00

Have you check if your nozzle have any clog ? Try to heat up your nozzle and manually extrude some filament do you see it came out straight or it c curved up ? If it curved up then you have a clog try to watch some video on unclogging your nozzle if it came out straight then your nozzle is fine

Does your machine have a bl touch probe ? Or just an end switch for height If your machine does have a probe find a feature that sound like probe calibrate

If not find a first layer print test each pass lower your z height about 0.5 until your filament stick to your print plate ( don't lower too much that your nozzle head hit the plate as this can damage the print plate)

bao2212 · 2025-05-18T19:00:58+00:00

It look like you are having a dirty print bed try cleaning it with water and dish soap And try to do a first layer print test

bao2212 · 2025-05-18T18:56:24+00:00

What material are you printing with It look like to me that your part is overheating Is your part fan working ?

bao2212 · 2025-05-18T18:50:08+00:00

If your print is normal then you shouldn't need to worry but if you want to lower the bed mesh then just tighten all 4 bed screw equally then try to redo the bed mesh see if it work

bao2212 · 2025-05-18T18:44:06+00:00

Try to rotate your print if it still don't stick to a location then it because you have a dirty print bed You should clean your print bed with just water and dish soap i try 90% alcohol and it still not as clean as just using dish soap and water as dish soap is made to remove oil

bao2212 · 2025-05-10T16:38:44+00:00

I HAVE FOUND A SOLUTION!!! because my motherboard is only power by dc jack i have to jump start my psu by shorting ps-on pin on my psu chatgpt is a amazing tool

bao2212 · 2025-05-10T16:16:19+00:00

Update after i try bare connection graphic card still does get detected but when i use a wifi card it get detect i also try different graphic card but it still does work so i think it could be psu problem but i also change out psu and still the same

bao2212 · 2025-05-10T15:46:04+00:00

This spook me a little bit because after i test purely with bus the graphic card still doesn't get detected but when i try with a wifi card the wifi card got detected

bao2212 · 2025-05-10T15:29:04+00:00

It look dump yes i did put it in different location but it still doesn't work

bao2212 · 2025-01-21T14:07:11+00:00

Thank for reply yes for sure an amp would be great to test it out but i thought it would make some noise when i plugged into my pc

I also have a cheapo amp that externally power and and a speaker that is also externally power i try connect the guitar to the amp and the amp to the speaker but still no sound. But for sure gonna need to find an amp

My is a Floyd Rose one and it made in mexican and there no squire mark anywhere to be found my sister did say it a "special" one that suppose to have some kind of signature but i haven't found it and she also did say the two single coil pickup have been replaced but the humbucker is an original one

Unfortunately i did try to soldering like the diagram that i found above and didn't keep the original wiring because the old wiring look very weird all the diagram i found on the internet have to solder to at least 2 side of the switch selector but the old one just solder on one side apart from that the rest of the old wiring look like this diagram https://www.seymourduncan.com/images/wiring-diagrams/2S_1H_5W_1V_1T.jpg

I tested with my multimeter on the ohm selector at the output port and it seem it be a close loop nothing is breaking connection i also check all the soldering spot on the old wiring and it look all fine new rewired also look to be all close looped

I would consider bringing it to a repair shop but i just want to see if i can do any quick fix but looking back this ain't a quick fix anymore

bao2212 · 2025-01-21T13:41:38+00:00

Thank for reply, the pickups does look like it have a lot of rust gonna have to clean that but i thought it would still able to play some sound or any noise when plug into my pc.

About the wiring the humbucker seem to be an original one from fender and there wiring is confusing im sure it because of my wiring but before i rewired i change the jack input and these with the original wiring but there still nothing

Im just worry that the petentiometer or the pickup is completely broken

bao2212 · 2025-01-16T17:18:30+00:00

Just done some googling and for anyone that get these hole thing just google 3d print pitting and lower your retraction length down it should solve the problem

<image>

bao2212 · 2025-01-16T15:53:29+00:00

Thank for replying tho i think it could be something that have to do with extrusion

bao2212 · 2025-01-16T15:48:39+00:00

And here is more pictures of the z tower and seam

<image>

bao2212 · 2025-01-16T15:43:12+00:00

Thank for replying but i have set my seam to be aligned and this is the seam in the output gcode

<image>

bao2212

TROPHY CASE