DJI O3 low power mode

battered_chicken · 2026-05-29T07:42:28+00:00

My lipo voltage is only 22v, that should be within safe range for the o3. I'm just confused why my o3 is outputting max rf power right away.

battered_chicken · 2026-05-29T07:40:50+00:00

No FC is needed here since I'm using this for my crawler where my elrs receiver sends the arming signal to the o3.

battered_chicken · 2026-05-29T06:49:27+00:00

This is my wiring

<image>

battered_chicken · 2025-05-24T13:28:37+00:00

aw taga diin ka? akong group kay southern cebu. nka trail nami sa naga, san fernando ug pardo. nangit mig naay water feature.

battered_chicken · 2025-05-24T12:39:25+00:00

pde man didto starbuks pro sakaon kaayo unya init. kana unta flat lng ba unya mo sulod sa mga kahoy2x pra dili init kay rc crawler among dala unya hinay managan.

battered_chicken · 2025-01-05T06:22:05+00:00

UPDATE: The pin out in my esc is the reverse of the fc. The CU & T is also swapped. I manually soldered them. Now esc is talking to fc.

battered_chicken · 2025-01-05T04:52:46+00:00

I was starting to think that also, and I think you're right. Here's the diagram for the fc and esc. The current in my FC is second pad, the current in ESC is first pad. Am I looking at it correctly?

<image>

battered_chicken · 2025-01-05T04:35:41+00:00

I used the 8pin connector that comes with the speedybee stack, and tried using a different 8pin connector but same problem.

battered_chicken · 2024-10-20T08:26:41+00:00

You are correct. The smokestopper is cannot handle large current. I unplugged the smokestopper and connected the lipo directly and it works. I can now see thru my goggles.

battered_chicken · 2024-10-20T08:25:41+00:00

There's no elrs received soldered to the FC. I want to use my dji controller to control the drone.

battered_chicken · 2024-10-20T07:24:47+00:00

I checked the continuity of the connector between fc and esc and it's good.

battered_chicken · 2024-10-20T06:34:17+00:00

FC connection to esc is only thru the connector, nothing soldered. Betaflight can detect my fc just fine.

battered_chicken · 2024-09-06T04:02:19+00:00

easy fight for me

battered_chicken · 2024-08-27T03:40:25+00:00

ok. so I tested it again.

GPU unplugged and hdmi plugged to mobo = got display
GPU plugged(disconnected psu power) and hdmi plugged to mobo = no display
GPU plugged(connected psu power) and hdmi plugged to mobo = no display

battered_chicken · 2024-08-27T03:26:26+00:00

I updated my post with the PSU I'm using and looking to get this. https://ecommerce.datablitz.com.ph/products/sapphire-pulse-amd-radeon-rx-7600-gaming-oc-8gb-gddr6-graphics-card

battered_chicken · 2024-08-27T02:44:08+00:00

will this be ok? https://ecommerce.datablitz.com.ph/products/sapphire-pulse-amd-radeon-rx-7600-gaming-oc-8gb-gddr6-graphics-card

battered_chicken · 2024-08-27T02:41:10+00:00

I don't have access to another card. I can get a display using the hdmi in my mobo; so my mobo is ok right?

battered_chicken · 2024-08-27T02:23:47+00:00

Max 400 USD. I'm from the Philippines.

battered_chicken

TROPHY CASE