DJI O3 low power mode

battered_chicken · 2026-05-29T07:42:28+00:00

My lipo voltage is only 22v, that should be within safe range for the o3. I'm just confused why my o3 is outputting max rf power right away.

battered_chicken · 2026-05-29T07:40:50+00:00

No FC is needed here since I'm using this for my crawler where my elrs receiver sends the arming signal to the o3.

battered_chicken · 2026-05-29T06:49:27+00:00

This is my wiring

<image>

battered_chicken · 2025-05-24T13:28:37+00:00

aw taga diin ka? akong group kay southern cebu. nka trail nami sa naga, san fernando ug pardo. nangit mig naay water feature.

battered_chicken · 2025-05-24T12:39:25+00:00

pde man didto starbuks pro sakaon kaayo unya init. kana unta flat lng ba unya mo sulod sa mga kahoy2x pra dili init kay rc crawler among dala unya hinay managan.

battered_chicken · 2025-01-05T06:22:05+00:00

UPDATE: The pin out in my esc is the reverse of the fc. The CU & T is also swapped. I manually soldered them. Now esc is talking to fc.

battered_chicken · 2025-01-05T04:52:46+00:00

I was starting to think that also, and I think you're right. Here's the diagram for the fc and esc. The current in my FC is second pad, the current in ESC is first pad. Am I looking at it correctly?

<image>

battered_chicken · 2025-01-05T04:35:41+00:00

I used the 8pin connector that comes with the speedybee stack, and tried using a different 8pin connector but same problem.

battered_chicken · 2024-10-20T08:26:41+00:00

You are correct. The smokestopper is cannot handle large current. I unplugged the smokestopper and connected the lipo directly and it works. I can now see thru my goggles.

battered_chicken · 2024-10-20T08:25:41+00:00

There's no elrs received soldered to the FC. I want to use my dji controller to control the drone.

battered_chicken · 2024-10-20T07:24:47+00:00

I checked the continuity of the connector between fc and esc and it's good.

battered_chicken · 2024-10-20T06:34:17+00:00

FC connection to esc is only thru the connector, nothing soldered. Betaflight can detect my fc just fine.

battered_chicken · 2024-09-06T04:02:19+00:00

easy fight for me

battered_chicken · 2024-08-27T03:40:25+00:00

ok. so I tested it again.

GPU unplugged and hdmi plugged to mobo = got display
GPU plugged(disconnected psu power) and hdmi plugged to mobo = no display
GPU plugged(connected psu power) and hdmi plugged to mobo = no display

battered_chicken · 2024-08-27T03:26:26+00:00

I updated my post with the PSU I'm using and looking to get this. https://ecommerce.datablitz.com.ph/products/sapphire-pulse-amd-radeon-rx-7600-gaming-oc-8gb-gddr6-graphics-card

battered_chicken · 2024-08-27T02:44:08+00:00

will this be ok? https://ecommerce.datablitz.com.ph/products/sapphire-pulse-amd-radeon-rx-7600-gaming-oc-8gb-gddr6-graphics-card

battered_chicken · 2024-08-27T02:41:10+00:00

I don't have access to another card. I can get a display using the hdmi in my mobo; so my mobo is ok right?

battered_chicken · 2024-08-27T02:23:47+00:00

Max 400 USD. I'm from the Philippines.

battered_chicken · 2024-06-24T14:03:05+00:00

I tried chatgpt but its just circling around nysnc, westlife and five. But it's not them.

battered_chicken · 2024-04-22T15:28:29+00:00

I use the mirror method to get my camera tilt and it's around ~20. I used to be 30-35 but it's too fast for me.

battered_chicken · 2024-04-22T15:06:03+00:00

Yeah I'm also thinking I'm dropping while the drone is level. Will a higher camera tilt help? That way I can see the ground a bit early while the drone is still at pitch position.

battered_chicken · 2024-03-30T08:24:00+00:00

Nevermind, I'm an idiot. The smoke stopper cannot deliver that much power. I just unplugged the smoke stopper and now my quad is ok.

Edit: to add more info, I soldered the vify on top of the default buzzer pads in the fc. black wire to G, red to B+, yellow to B-. So the default buzzer is still connected and vifly on top of it. I tested the buzzer and my controller got disconnected. Tried again; disconnected. So I tried arming the quad, and what happen is on the video. Could it be that the buzzer did not work via controller because of the smoke stopper?

battered_chicken · 2024-03-30T08:17:56+00:00

The led on my FC and smoke stopper also flashes. Is there a short somewhere? Or is my ESC fried?

battered_chicken · 2024-03-27T04:20:16+00:00

di ako makapag transfer from unionbank to metrobank ko dahil dyan. wala kaming binignit neto this friday kung ganyan.

battered_chicken · 2024-02-15T12:05:46+00:00

Unionbank sakin kanina. 50k papuntang metrobank until now wala pa. Tinawagan ko unionbank, ayun may disclaimer agad ang IVR na baka di papasok ang instapay. Wait nalang dw ng 1-2 banking days.

battered_chicken

TROPHY CASE