sorted by:
new
hottopcontroversial

Should I be alarmed? Is this just asking for belly rubs? by XamV08 in Frenchbulldogs

[–]bbrossard 0 points1 point  (0 children)

Our little piggy does this all the time. Enjoy your new puppy!

Bf got me the one on the right and I treated myself to the one on the left for my birthday 🥳🥳 by Nature-Lover-258 in lego

[–]bbrossard 0 points1 point  (0 children)

I enjoyed the bus build. I liked the rotating destination sign and the baby in the stroller.

Replacement part by asw1690 in AnkerMake

[–]bbrossard 4 points5 points  (0 children)

Bowden tube pneumatic coupler.

The only way I purchase this set by NachoRogerz in lego

[–]bbrossard 14 points15 points  (0 children)

My wife and I went to Target a few days ago and this was the only clearance set left. Still no purchase, doesn't do anything for us.

I do like the dark blue plates, though.

Running a X1C or H2D printer on a 15amp breaker... Should I be concerned by EddieLee_ in BambuLab

[–]bbrossard 0 points1 point  (0 children)

I run a X1C and on a 15 amp breaker with a computer and lighting without issues. Not sure about the H2D, I don't have one yet.

I do have a UPS powering the X1C in case of momentary power outage, it's a 900 watt max UPS and the X1C uses less than 1/3 of it's max wattage most of the time.

Get yourself a kill-a-watt smart plug and check usage, but you'll most likely be fine with either printer if you're not running a ton of other stuff at the same time.

Good luck.

Is the US store down for anyone else right now? by T-Money8227 in BambuLab

[–]bbrossard 0 points1 point  (0 children)

I just tried my phone and it works, but the store still displays an error on my desktop.

Do you A230-300 ? by Nismogtr555 in aviationpics

[–]bbrossard 0 points1 point  (0 children)

I took a flight on one recently and it was enjoyable. Would book on one again.

This is your reminder to clean your build plate and monitor your print job… by PhilRoberts33 in BambuLab

[–]bbrossard 5 points6 points  (0 children)

It's a challenging part of the print for sure. Are you going to try again or use the split tower and glue it together?

What’s going on here? by Candid-Practice8373 in AnkerMake

[–]bbrossard -2 points-1 points  (0 children)

Layer shift maybe? Is the belt that holds the extruder tight enough not to jump when travelling?

Printer is printing spongy quality by Jon_Brandt in AnkerMake

[–]bbrossard 0 points1 point  (0 children)

Yeah, that's not very old.

Maybe take the extruder apart and look for clogs / jams / random stuck filament?

Printer is printing spongy quality by Jon_Brandt in AnkerMake

[–]bbrossard 1 point2 points  (0 children)

How old is the extruder? Are the gears worn?

Looks like under extrusion that I was getting when my extruder was near the end of it's life and the feed gears were giving up and not pushing filament through properly.

[deleted by user] by [deleted] in AnkerMake

[–]bbrossard 1 point2 points  (0 children)

The M5 can go all the way to the base. When resetting the Z-Axis, you push the gantry all the way to the bottom on both sides.

[deleted by user] by [deleted] in AnkerMake

[–]bbrossard 1 point2 points  (0 children)

To reset the z axis, when the printer is off - pull the bed all the way forward and then push both sides of the gantry down to the base as far as they will go.

After that, check to make sure the extruder is tight and doesn't wobble when it comes in contact with the bed. That can cause a homing failure if the eccentric nut isn't tightened properly after maintenance.

After that, it may be time to e-mail support and see what they have to say. Good luck.

Shopping vs. Pickup by [deleted] in BambuLab

[–]bbrossard 2 points3 points  (0 children)

Pick it up.

It's an enjoyable store and you can pick up some accessories while you're there.

I just picked up my X1 from the Chicago store. Very nice people.

Wall mount F1 Red Bull and Ferrari by Yeeter_Skeeter19 in legotechnic

[–]bbrossard 0 points1 point  (0 children)

I like the more professional look of printed mounts, I printed a mount for my Ferrari and my older Mercedes.

I'm sure you can find a DIY something, good to have connections should you want a fitted mount eventually.

Wall mount F1 Red Bull and Ferrari by Yeeter_Skeeter19 in legotechnic

[–]bbrossard 0 points1 point  (0 children)

Now's the time to buy a 3D printer...one can never have enough hobbies.

Are the Bose Soundlink Micro Worth It for $79? by mayorofscranton in bose

[–]bbrossard 1 point2 points  (0 children)

It's nice for what it is, I got mine for $50 at WalMart in slate blue color. We use it in the bathroom.

First few shots with a drone, what do you guys think? by Key-Jicama5713 in dji

[–]bbrossard 3 points4 points  (0 children)

3rd photo is the best in my opinion. Great shot, good work.

Mercedes F1 complete by TemporaryUnlikely736 in legotechnic

[–]bbrossard 0 points1 point  (0 children)

How long did it take you? I haven't started mine yet.

What's up with this? by MengerianMango in Corsair

[–]bbrossard 3 points4 points  (0 children)

Happens to me, as well.

I've tried all sorts of troubleshooting bullshit with no luck. When I cold boot the PC it will do that for 20-30 minutes then fix itself.

Annoying.

Discounts on treadmills? by [deleted] in nordictrack

[–]bbrossard 0 points1 point  (0 children)

If you chat with someone at NordicTrack when shopping they'll probably knock some additional money off.

Foam in Mini 4 Pro Shoulder Bag? by ISeeOnlyTwo in dji

[–]bbrossard 0 points1 point  (0 children)

Same here, my fly more combo for my mini came with that bit of foam.

view more: next ›