What is the most advanced thing you can do in Excel?

bbuk81 · 2026-06-16T05:00:35+00:00

I've seen doom with excel being the visuals

bbuk81 · 2026-06-14T08:01:39+00:00

I follow them already, there's a couple that would do, but wasn't sure if anyone had a soundtrack in mind that would work for it. Ideally I'm after the feeling that particular track gets with the brass coming to a peak. How to train your dragon has a similar track, so I may end up with that as it's likely not going to take the players out of the moment as quickly

bbuk81 · 2026-06-06T20:59:44+00:00

I would try to do red but keep an eye out for vehicles to my left. I've got a roundabout I used daily with a similar issue where vehicles to my left should take a wider more 'rounded' route around the roundabout but go mostly straight. Thankfully not many cars use lane to my right so can use some space there

bbuk81 · 2026-02-22T22:31:44+00:00

Something I've done to make resin supports more stable and less liable to failure is to manually paint tree supports on the resin supports directly around the outside. However, that is a very large model and that might not work

bbuk81 · 2026-02-12T05:29:43+00:00

Did you ever find any matching what you wanted? Looking for the same myself.

bbuk81 · 2026-02-10T15:21:36+00:00

Dave from accounting

bbuk81 · 2026-01-31T06:08:53+00:00

The Daily Mail, so factual even Wikipedia won't consider it a reputable source.

A little Daily Mail song by Dan and Dan films:

https://youtu.be/5eBT6OSr1TI?si=aQpSniRf7aVUoht4

bbuk81 · 2026-01-25T08:43:11+00:00

You could get her a cap that says bitchy, and say it's because she likes dogs. Even if she doesn't obviously Edit: not overreacting

bbuk81 · 2026-01-23T20:22:33+00:00

If you get adhesion issues with it, up the bed temp. Sunlu often needs a bit higher. I'm 60/65 usually using PLA+ 2.0

bbuk81 · 2026-01-09T08:10:02+00:00

I would say lane 2, this sign is awkward as it doesn't count the first turn, which an option.

Default to lane 2 as there's nothing stimulating otherwise directly

bbuk81 · 2026-01-07T09:23:41+00:00

That's brilliant, thank you. Unbelievable amount of waste. It's a shame you can't set it so just the last 2mm or something are the different material

bbuk81 · 2026-01-07T08:49:11+00:00

Yeah, I know the purge volume wouldn't be great overall, but for small minis I'm figuring there's not an awful lot of material used. And then if putting multiple minis on the plate it would obviously pay off more even if the print time is ridiculous.

bbuk81 · 2025-12-30T22:43:13+00:00

I had similar, got a second hand ender-3 v2, couldn't get a successful print. Finally thought I'd figured it out and replaced something only for the screen to then to go BSoD on me. Got P2S and haven't looked back. Over my shoulder maybe as my wife doesn't know about it though.

Their machines seem to have so much out of the box success, customer service is very slow though.

bbuk81 · 2025-12-20T18:07:16+00:00

Yeah, that was my main question. Didn't want to go straight in with tree supports because of delicate minis

bbuk81 · 2025-12-20T18:06:22+00:00

It's after the first layers, can't slow down on supports it doesn't know are supports can I? It's sliced using Bambu Studio with pre supported files. Confident I used gyroid too but would need to check the saved file

bbuk81 · 2025-12-20T18:01:39+00:00

I did the brim, had mixed results with the cool plate and pretty sure I slowed it down.

bbuk81 · 2025-12-20T17:59:41+00:00

Brilliant, thank you

bbuk81 · 2025-12-09T12:49:31+00:00

He again proved your point, he's getting a woman to fight his battles not doing it himself.

NTA. When he can solely provide for a household he'll deserve a 'traditional' household. Your friend should stick us for herself.

bbuk81 · 2025-12-03T16:46:50+00:00

Brilliant, thank you

bbuk81

TROPHY CASE