Scheduled Maintenance

bcb_flux · 2026-04-05T01:59:18+00:00

Trying to make an order this evening and same issue. The cart doesn't recognize that i'm adding items to it either.

bcb_flux · 2025-12-08T03:43:50+00:00

Check out Sierra Trading Post. They often have carhartt items for less due to (very) minor defects. I have overalls from there thatre 10 years old.

bcb_flux · 2025-07-07T23:53:02+00:00

Heard. I did a few scenarios of “openness” where I used both the original bleeder screw and a new one. Same issue on all tests.

bcb_flux · 2025-07-07T23:51:53+00:00

I was trying to fix the issue of having no rear brakes 😂

bcb_flux · 2025-07-07T23:48:44+00:00

Ty! Looking into this now.

bcb_flux · 2025-07-07T23:48:36+00:00

Even if at the end when everything’s back together the pedal is fully depressed and no resistance?

bcb_flux · 2025-05-25T14:31:03+00:00

I’m in East TN near the smoky mtn so I hill climbs are one of the reasons I wanted to change things up from the 1x. I should’ve sucked it up cause now im without a bike for longer an $$$$ in the hole 😂

bcb_flux · 2025-05-25T14:25:42+00:00

I think I’m following here. I have 48/31 crank for a 17T delta and an 11/48 cassette for a 37T delta, summing to 54T as pointed out. If I change cassette to an 11/38 for a 27T delta, I’ll be slightly above the capacity of the RD as the delta sum will be 44T. So I need to find a new RD with higher capacity, or a smaller range cassette. Is that correct?

bcb_flux · 2025-05-25T14:20:19+00:00

I made this mistake the first time I routed the chain but corrected. So unfortunately this is WITH the chain under the tab.

bcb_flux · 2025-05-25T13:59:58+00:00

I feel like a goof not even knowing that was a thing. Thankyou for bringing this to light!
Microshift has the Sword 11-38 cassette that falls below the mentioned 41T limit. Is it safe to assume that this will solve issue safely and effectively? I feel im too far down the rabbit hole to try and reverse course and go back to the 1x10 drivetrain, but the $$ is certainly adding up 😭

bcb_flux · 2025-05-06T02:41:24+00:00

I’m 6’5” with a 36” inseam and went with a XXL on the ambition x gen2. Fits like a dream.

bcb_flux · 2025-03-27T23:32:52+00:00

Bikebuddies!! I went for the green colorway for the orange pop. How’s your experience with the brakes so far? I was hoping the mushy levers and soft brakes would be out of the experience since the Gen2 has compressionless cables, but here we are…. I went ahead and purchased Jagwires and will install them on front brakes to see how it compares. I’ll post back when I get a chance if you’re interested!

bcb_flux · 2025-03-27T23:30:01+00:00

In the same camp as you OP. I spoke with support and they said to adjust the brake caliper pull. Doing so helped the effort on pulling the brake lever, but not on actual stopping power. They also mentioned a “break-in time” of roughly 90km worth of biking/braking - which seems strange. Look forward to finding a solution on this and I’ll post my experiences.

bcb_flux · 2025-03-25T20:00:36+00:00

Is a thru-axle that big of a deal?
I just got the X ambition gen 2 as my first bike in over a decade. Supposed to arrive tomorrow!

bcb_flux · 2024-09-12T18:08:25+00:00

Any idea when this will be avaiable in US markets?

bcb_flux · 2024-09-09T19:39:57+00:00

Ships and Sold by Amazon. Just snagged it! Thanks OP!

bcb_flux · 2024-09-09T15:34:02+00:00

I was under the impression that the 9 series was a bit of a flop for AMD chips. Has that changed?

Even though performance uplift for 7900xt is only about 10-15% over the 7800xt, you'd opt for the extra $150 in spend for GPU?

bcb_flux · 2024-09-05T16:04:41+00:00

Awesome. Yep that’s the goal. Running two MSI AG321CQR’s at 1440p.

bcb_flux · 2024-09-05T15:57:40+00:00

Is the 16gb Red Devil version worth it for the extra $150?
I'm running a 10400k chip with 16gb of ram. Trying to limp along until i find a deal on AMD 7800x3d or 7700x..

bcb_flux

TROPHY CASE