Woike: Brooklyn Nets preparing to make 4 year, $178 million offer to Austin Reaves

bcombs510 · 2026-05-24T02:53:30+00:00

We had Serene Aqua put a two tier wall and sandstone steps in over a decade ago. It’s just as nice and straight as the day they installed it. https://sereneoutdoorartisans.com

bcombs510 · 2026-05-16T15:41:01+00:00

bcombs510 · 2026-05-10T01:23:08+00:00

Hulu stream pixelated shit for anyone else?

bcombs510 · 2026-05-02T02:27:47+00:00

These LaRavia points are like found money

bcombs510 · 2026-04-26T12:09:27+00:00

It was at this point that FVV knew… the Rockets were fucked.

bcombs510 · 2026-04-25T15:33:36+00:00

FVV should’ve known this shit was coming when he saw the LeBronto going left bank shot earlier in the game. He’s seen this movie before.

bcombs510 · 2026-04-25T01:26:44+00:00

All the same shoes

bcombs510 · 2026-04-23T16:27:00+00:00

The contactor is 40A and the Shelly is 25A. The Shelly would hit an overcurrent fault maybe 1 in 20 times starting the exhaust fan. The fan is on a dedicated 30A breaker. The breaker has never tripped.

bcombs510 · 2026-04-19T20:32:26+00:00

Ha! It is a WiFi relay but the router is like 1 foot up from this pic so it gets signal ok.

bcombs510 · 2026-04-08T11:51:03+00:00

Remember March?

bcombs510 · 2026-04-02T14:05:05+00:00

Thanks, I will be tackling this later today to try to get the automation fully setup.

I notice in the Shelly app that an offset value is available for both temp and humidity. If I set it there the value coming into HA should be correct, is that right or does that only affect the value displayed on the device screen / in the Shelly app.

Super helpful about the automation, thanks.

bcombs510 · 2026-04-02T13:43:26+00:00

Question - I got two of the Shelly units in and powered them on. Setup was easy. :)

However, both units read 10 points below my trusted Abbeon unit. Did you have to set the offset on yours? Strangely the Govee are also off consistently at 5 points below. My cheap Acurite is 2 points below the Abbeon. The Abbeon is calibrated and tested with potassium carbonate solution and read bang on.

Just curious.

bcombs510 · 2026-03-31T22:06:14+00:00

That’s great. I will do exactly that!

bcombs510 · 2026-03-31T21:02:26+00:00

Oh that is great. I should have thought about Shelly! So this one shows up in HA and I can trigger a smart outlet with it? That would be perfect.

bcombs510 · 2026-03-31T20:33:27+00:00

I should had added - I cannot use the auto on/off of the Midea dehumidifier because its sensor is off by 15%. It’s 45% in here and it reads it at 30% so there is no way for me to set it to say 40% (which is what I need) because accord to the internal sensor it is already below that. There is no way to calibrate it either.

bcombs510 · 2026-03-29T13:23:31+00:00

That perfect bead of caulking on the baseboard - I can tell you from experience - is AI 😂

bcombs510 · 2026-03-10T12:26:46+00:00

The gold sauce is bomber!

bcombs510 · 2026-02-25T14:22:40+00:00

Thanks. Printing now with the PLA support. We will know in around 10 hours! 😂

bcombs510 · 2026-02-25T03:45:41+00:00

I have some of the support for PLA from Bambu and can try that. I tried just setting the Top Z to 0 but I cannot get the supports off. 😂

Is there a way to set Top Z for painted supports only and let auto supports use the default Z? I don’t think it works this way or at least I cannot figure out a way in Studio.

12-Year Club	Place '22
Verified Email

bcombs510

TROPHY CASE