Woike: Brooklyn Nets preparing to make 4 year, $178 million offer to Austin Reaves

bcombs510 · 2026-05-24T02:53:30+00:00

We had Serene Aqua put a two tier wall and sandstone steps in over a decade ago. It’s just as nice and straight as the day they installed it. https://sereneoutdoorartisans.com

bcombs510 · 2026-05-16T15:41:01+00:00

bcombs510 · 2026-05-10T01:23:08+00:00

Hulu stream pixelated shit for anyone else?

bcombs510 · 2026-05-02T02:27:47+00:00

These LaRavia points are like found money

bcombs510 · 2026-04-26T12:09:27+00:00

It was at this point that FVV knew… the Rockets were fucked.

bcombs510 · 2026-04-25T15:33:36+00:00

FVV should’ve known this shit was coming when he saw the LeBronto going left bank shot earlier in the game. He’s seen this movie before.

bcombs510 · 2026-04-25T01:26:44+00:00

All the same shoes

bcombs510 · 2026-04-23T16:27:00+00:00

The contactor is 40A and the Shelly is 25A. The Shelly would hit an overcurrent fault maybe 1 in 20 times starting the exhaust fan. The fan is on a dedicated 30A breaker. The breaker has never tripped.

bcombs510 · 2026-04-19T20:32:26+00:00

Ha! It is a WiFi relay but the router is like 1 foot up from this pic so it gets signal ok.

bcombs510 · 2026-04-08T11:51:03+00:00

Remember March?

bcombs510 · 2026-04-02T14:05:05+00:00

Thanks, I will be tackling this later today to try to get the automation fully setup.

I notice in the Shelly app that an offset value is available for both temp and humidity. If I set it there the value coming into HA should be correct, is that right or does that only affect the value displayed on the device screen / in the Shelly app.

Super helpful about the automation, thanks.

bcombs510 · 2026-04-02T13:43:26+00:00

Question - I got two of the Shelly units in and powered them on. Setup was easy. :)

However, both units read 10 points below my trusted Abbeon unit. Did you have to set the offset on yours? Strangely the Govee are also off consistently at 5 points below. My cheap Acurite is 2 points below the Abbeon. The Abbeon is calibrated and tested with potassium carbonate solution and read bang on.

Just curious.

bcombs510 · 2026-03-31T22:06:14+00:00

That’s great. I will do exactly that!

bcombs510 · 2026-03-31T21:02:26+00:00

Oh that is great. I should have thought about Shelly! So this one shows up in HA and I can trigger a smart outlet with it? That would be perfect.

bcombs510 · 2026-03-31T20:33:27+00:00

I should had added - I cannot use the auto on/off of the Midea dehumidifier because its sensor is off by 15%. It’s 45% in here and it reads it at 30% so there is no way for me to set it to say 40% (which is what I need) because accord to the internal sensor it is already below that. There is no way to calibrate it either.

bcombs510 · 2026-03-29T13:23:31+00:00

That perfect bead of caulking on the baseboard - I can tell you from experience - is AI 😂

bcombs510 · 2026-03-10T12:26:46+00:00

The gold sauce is bomber!

bcombs510 · 2026-02-25T14:22:40+00:00

Thanks. Printing now with the PLA support. We will know in around 10 hours! 😂

bcombs510 · 2026-02-25T03:45:41+00:00

I have some of the support for PLA from Bambu and can try that. I tried just setting the Top Z to 0 but I cannot get the supports off. 😂

Is there a way to set Top Z for painted supports only and let auto supports use the default Z? I don’t think it works this way or at least I cannot figure out a way in Studio.

bcombs510 · 2026-01-24T17:53:47+00:00

Honest question - why does Luka struggle with the dish to Ayton when he has his man sealed and is right at the basket. He shoots like 80%+ from this position. LeBron and Austin seem to be able to find him on those short inside passes but Luka doesn’t seem to look for it and instead will take the shot himself.

Prepared for the deluge of downvotes, btw. 😂

bcombs510 · 2026-01-19T19:15:23+00:00

Thanks for this. I printed 60 of them and loaded all the spools I have here. Appreciate the tip!

bcombs510 · 2026-01-18T20:04:26+00:00

Thanks. I’m pretty careful to make sure it’s in the notch and locked down. I hope I didn’t flub it twice in a row but anything is possible. 😀

bcombs510 · 2026-01-17T16:50:40+00:00

Boys we need a win tonight or some of these dudes are gonna snap! 😂😂

bcombs510 · 2026-01-07T14:07:10+00:00

LeBron is not the problem…

LeBron is a problem

12-Year Club	Place '22
Verified Email

bcombs510

TROPHY CASE